Engine Oil Pan
Show/hide table
Illustration 1 | g03356623 |
Show/hide table
Specification for 117-0060 Oil Pan Gp | |||
Item | Qty | Part | Specification Description |
1 | - | - | As required, apply red Loctite 596 to the gasket joints before assembly. |
2 | 10 | 1A-2029 Bolt | Use the following procedure in order to tighten the bolts of the plate: 1. Tighten five bolts (3) to a standard torque. 2. Tighten bolt 1 through bolt 10 in a numerical sequence that is shown in Illustration 1 to a standard torque. |
3 | 5 | 1A-2029 Bolt | |
4 | 2 | 6V-4315 O-Ring Seal | Lubricate the bore of the O-ring seals lightly with the lubricant that is being sealed or an approved equivalent. |
5 | 50 | 5P-5855 Bolt | As required, apply blue Loctite 242 to the open top end of the bolt holes after assembly of the oil pan. |
6 | 1 | 142-4159 Integral Seal | As required, apply red Loctite 596 to the sealing surface of the integral seal before assembly. |
7 | 2 | 3P-0654 O-Ring Seal | Lubricate the bore of the O-ring seals lightly with the lubricant that is being sealed or an approved equivalent. |
8 | - | - | Before assembly, as required apply red Loctite 596 on the connecting joint of the front accessory drive housing and the front of the cylinder block. |
9 | 4 | 5P-5700 O-Ring Seal | Lubricate the bore of the O-ring seals lightly with the lubricant that is being sealed or an approved equivalent. |
10 | 1 | 6I-0723 Oil Drain Plug | Torque to Lubricate the bore lightly with the lubricant that is being sealed. |
11 | - | - | Before assembly, as required apply red Loctite 596 on the connecting joint of the flywheel housing and the rear of the cylinder block. |
12 | 1 | 4B-2363 Oil Drain Plug | Torque to |
Caterpillar Information System:
C13, C15, and C18 Tier 4 Final Engines Valve Mechanism Cover
C13, C15, and C18 Tier 4 Final Engines Valve Mechanism Cover
C13, C15, and C18 Tier 4 Final Engines Engine Oil Filter Base
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Engine Oil Cooler Bypass and Cooling Jet Sequence Valves
XQ400 Power Module Gas Pressure Regulator Condensation - Drain
CG137-08 and CG137-12 Engines Coolant Level - Check
C15 Generator Sets Model View Illustrations
HVOF Identification and Polishing (Superfinishing){0674, 0679, 1000, 7000, 7562} HVOF Identification and Polishing (Superfinishing){0674, 0679, 1000, 7000, 7562}
992K Wheel Loader Fuel Tank Strainer - Clean
2011/06/24 An Additional One-Piece Steel Piston Is Available for Cylinder Packs That Are Utilized in Certain C15 On-Highway Truck Engines {1214, 1225}
C15 and C18 Tier 4 Final Engines Swirl Plate (ARD Combustion) - Inspect/Clean
C13, C15, and C18 Tier 4 Final Engines Engine Oil Filter Base
C4.4 Industrial Engine Crankshaft Gear (Balancer Drive) - Remove and Install
349F and 352F Excavators Machine System Specifications Relief Valve (One-Way Hydraulic Flow)
C15 Petroleum Generator Set Engines Fuel Pressure Sensor
3500B Engines for Caterpillar Built Power Modules Water Pump
320E, 320F, 323E, 323F, 324E, 326F, 329E, 329F and 330F Excavators Tool Control System Solenoid Valve (Proportional Reducing) - Calibrate - Flow Limit Valves
320E, 320F, 323E, 323F, 324E, 326F, 329E, 329F and 330F Excavators Tool Control System Combined Function - Electric Control: Relief Valve (Line) - Test and Adjust
320E, 320F, 323E, 323F, 324E, 326F, 329E, 329F and 330F Excavators Tool Control System Combined Function - Electric Control: Default Value of Work Tool Parameters
C175-16 Petroleum Engines Exhaust Manifold
C13, C15, and C18 Tier 4 Final Engines Housing (Front)
C175-16 Marine Propulsion Engines Fuel Lines
C175-16 Petroleum Engines Flexible Coupling
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Piston and Rings - Two-Piece Piston