Piston and Rings
Show/hide table
图 1 | g02577696 |
Show/hide table
368-7822 活塞和连杆总成技术规格 | |||
项目 | 数量 | 零件 | 技术规格说明 |
1 | 1 | 223-9159 顶部活塞环 | 安装顶活塞环时使标有 "UP-1" 的一侧朝向活塞顶部。 色条朝向活塞环开口间隙的右侧。 |
新顶部活塞环的厚度为 |
|||
|
|||
缸套孔每增加 |
|||
2 | 1 | 238-2707 活塞环 | 安装中间活塞环时使标有 "UP-2" 的一侧朝向活塞顶部。 色条朝向活塞环开口间隙的右侧。 |
新中间活塞环的厚度为 |
|||
|
|||
缸套孔每增加 |
|||
3 | 1 | 246-5659 活塞环 | 装配时,机油控制环的弹簧端应与环两端缝隙成180 度。 色条朝向活塞环开口间隙的右侧或左侧。 |
新活塞中用于活塞控油环的槽宽为 |
|||
新活塞控油环的厚度为 |
|||
|
|||
缸套孔每增加 |
|||
4 | 1 | 180-7350 活塞销 | 将活塞插入活塞体和连杆中之前,应先用清洁的发动机机油润滑活塞销。 |
活塞销活塞裙内安装的成品轴承中的孔径为 |
|||
新活塞销的直径为 |
|||
新活塞销的长度为 |
|||
将挡圈 (5) 安装到活塞底部开口处。 请参阅插图 1。 | |||
6 | 1 | 151-5925 螺栓 | 拧紧扭矩至 |
在组装进缸体之前,先使用清洁的发动机机油彻底润滑区域 (A) 中的整个活塞。 | |||
活塞环安装完成之后,旋转活塞环使各端隙之间的距离呈 120 度。 |
Caterpillar Information System:
C13, C15, and C18 Tier 4 Final Engines Turbocharger
C13, C15, and C18 Tier 4 Final Engines Turbocharger
320E, 320F, 323E, 323F, 324E, 326F, 329E, 329F and 330F Excavators Tool Control System Medium Pressure Hydraulic System
2011/06/16 A New Flywheel Housing with Additional Holes for the Timing Pin Is Used on C175-16 Generator Set Engines {1157}
Using the 209-3153 Portable Hose Machine {0374, 0599, 0684, 0738, 5057} Using the 209-3153 Portable Hose Machine {0374, 0599, 0684, 0738, 5057}
2011/10/13 Replacement and Adjustment Procedures for the Fan Drive of Certain Commercial Engines {1359}
UPSB505 Uninterruptible Power Supply UPS Battery - 50Hz IGBT for CSIEN-CSION-CSPEN Circuit Board - Replace
UPSB505 Uninterruptible Power Supply UPS Battery - 50Hz Unit Final Check
UPSB505 Uninterruptible Power Supply UPS Battery - 50Hz Manual Transfer - Check
C32 Auxiliary Engine Cold Weather Starting
UPSB505 Uninterruptible Power Supply UPS Battery - 50Hz On-Battery - Check
C15 Generator Sets Safety Messages
C3.4B Engines For Caterpillar Built Machines Camshaft Bearings
C13, C15, and C18 Tier 4 Final Engines Engine Oil Filter Base
C15 and C18 Tier 4 Final Engines Swirl Plate (ARD Combustion) - Inspect/Clean
2011/06/24 An Additional One-Piece Steel Piston Is Available for Cylinder Packs That Are Utilized in Certain C15 On-Highway Truck Engines {1214, 1225}
992K Wheel Loader Fuel Tank Strainer - Clean
HVOF Identification and Polishing (Superfinishing){0674, 0679, 1000, 7000, 7562} HVOF Identification and Polishing (Superfinishing){0674, 0679, 1000, 7000, 7562}
C15 Generator Sets Model View Illustrations
CG137-08 and CG137-12 Engines Coolant Level - Check
XQ400 Power Module Gas Pressure Regulator Condensation - Drain
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Engine Oil Cooler Bypass and Cooling Jet Sequence Valves
C13, C15, and C18 Tier 4 Final Engines Engine Oil Filter Base
C13, C15, and C18 Tier 4 Final Engines Valve Mechanism Cover