Replacement and Adjustment Procedures for the Fan Drive of Certain Commercial Engines {1359}
- Engine:
- C13 (S/N: KWJ1-1151)
- Generator Set:
- C15 GEN SET (S/N: JJF1-667)
- Industrial Engine:
- C9.3 (S/N: C9N1-615)
- C15 (S/N: LDN1-1050; HAZ1-509)
- C18 (S/N: BDN1-1089)
Certain commercial engines are equipped with a different fan drive than what is given in the Operation and Maintenance Manual and the System Operation Testing and Adjusting Manual. The fan drive has a larger nut than what is specified in the manual.
Fan Drive Replacement Procedure
Show/hide table
Tools Needed     | |||
Tool     | Part Number     |
Part Description     |
Qty     |
A     | 144-0235     | Belt Tension Gauge     | 1     |
Show/hide table
Illustration 1 | g02633452 |
(A) 22 mm (0.86 inch) (1) Jam nut |
- Loosen jam nut (1) with a 2 5/8 inch wrench in the counter-clockwise direction.
- Loosen the adjustment bolt (2) in the counter-clockwise direction.
Show/hide table
Illustration 2 | g02633636 |
- Remove the fan drive belt.
- Install a new fan drive belt.
- Turn the adjustment bolt in the clockwise direction until the belt is tensioned properly. Use Tooling (A) in order to check the belt tension. Refer to Table 2 for the belt specifications.
Show/hide table
Table 2 Belt Size     Width
Belt Top Reference    Initial
Belt Tension (1)    Used
Belt Tension (2)    
15.24000 mm (0.6 inch)    
17.53 mm (0.69 inch)    
801 ± 44 N (180 ± 10 lb)    
378 ± 44 (85 ± 10)    Show/hide table( 1 ) Tension for new belt ( 2 ) Belt with over 30 minutes of operation at rated speed
- Use a suitable tool to tighten the jam nut.
Adjustment Procedure
Show/hide table
Tools Needed     | |||
Tool     | Part Number     |
Part Description     |
Qty     |
A     | 144-0235     | Belt Tension Gauge     | 1     |
- Loosen the jam nut with a 2 5/8 inch wrench in the counter-clockwise direction.
- Turn the adjustment bolt clockwise until the belt is tensioned properly. Use Tooling (A) in order to check the belt tension. Refer to Table 4 for the belt specifications.
Show/hide table
Table 4 Belt Size     Width
Belt Top Reference    Initial
Belt Tension (1)    Used Belt Tension (2)    
15.24000 mm (0.6 inch)    
17.53 mm (0.69 inch)    
801 ± 44 N (180 ± 10 lb)    
378 ± 44 (85 ± 10)    Show/hide table( 1 ) Tension for new belt ( 2 ) Belt with over 30 minutes of operation at rated speed
- Use a suitable tool to tighten the jam nut.
Caterpillar Information System:
UPSB505 Uninterruptible Power Supply UPS Battery - 50Hz IGBT for CSIEN-CSION-CSPEN Circuit Board - Replace
UPSB505 Uninterruptible Power Supply UPS Battery - 50Hz Unit Final Check
UPSB505 Uninterruptible Power Supply UPS Battery - 50Hz Manual Transfer - Check
C32 Auxiliary Engine Cold Weather Starting
UPSB505 Uninterruptible Power Supply UPS Battery - 50Hz On-Battery - Check
C15 Generator Sets Safety Messages
UPSB505 Uninterruptible Power Supply UPS Battery - 50Hz DC Bus Voltage - Test
TA19 Agriculture Transmission Electronic Control System MID 081 - CID 0177 - FMI 03
TA19 Agriculture Transmission Electronic Control System Transmission, SPN 1542 - FMI 4
TA19 Agriculture Transmission Electronic Control System Transmission, SPN 1542 - FMI 3
C3.4B Engines For Caterpillar Built Machines Fuel Filter Base - Primary Fuel Filter Base
320E and 323E Excavators Machine System Specifications Relief Valve (Negative Flow Control)
Using the 209-3153 Portable Hose Machine {0374, 0599, 0684, 0738, 5057} Using the 209-3153 Portable Hose Machine {0374, 0599, 0684, 0738, 5057}
2011/06/16 A New Flywheel Housing with Additional Holes for the Timing Pin Is Used on C175-16 Generator Set Engines {1157}
320E, 320F, 323E, 323F, 324E, 326F, 329E, 329F and 330F Excavators Tool Control System Medium Pressure Hydraulic System
C13, C15, and C18 Tier 4 Final Engines Turbocharger
C13, C15, and C18 Tier 4 Final Engines Turbocharger
C13, C15, and C18 Tier 4 Final Engines Piston and Rings
C3.4B Engines For Caterpillar Built Machines Camshaft Bearings
C13, C15, and C18 Tier 4 Final Engines Engine Oil Filter Base
C15 and C18 Tier 4 Final Engines Swirl Plate (ARD Combustion) - Inspect/Clean
2011/06/24 An Additional One-Piece Steel Piston Is Available for Cylinder Packs That Are Utilized in Certain C15 On-Highway Truck Engines {1214, 1225}
992K Wheel Loader Fuel Tank Strainer - Clean
HVOF Identification and Polishing (Superfinishing){0674, 0679, 1000, 7000, 7562} HVOF Identification and Polishing (Superfinishing){0674, 0679, 1000, 7000, 7562}