Symbols
Show/hide table
磁场线路的接地导线 |
Show/hide table
设备零件内部接地的接地点 |
Show/hide table
注意 有关更多信息,请参阅手册。 |
Show/hide table
电击危险 |
Show/hide table
输入 |
Show/hide table
输出 |
Show/hide table
旁通输入开关 |
Show/hide table
直流 |
Show/hide table
交流 |
Show/hide table
相位 |
Show/hide table
正 |
Show/hide table
负 |
Show/hide table
空档 |
Show/hide table
注意 - 请参阅维修手册 |
Show/hide table
不可维修 |
Show/hide table
阅读维修手册 |
Show/hide table
远程通信连接 |
Show/hide table
并非接头 - 并非远程通信网络用接头。 |
Show/hide table
漏电电流高 - 连接电源之前有必要先接地。 |
Show/hide table
锂电池 - 如果电池更换不当的话,会有爆炸危险。 更换电池时应使用相同或等同的电池。 按照产品说明来处置废弃电池。 |
Show/hide table
散热片或支架未接地。 - 测试后再触摸。 |
Show/hide table
只可用于安全超低电压连接 |
Show/hide table
等待 5 分钟之后再断开任何电源或拆下任何盖板或面板。 |
Show/hide table
图 1 | g00785184 |
旁通输入 |
Show/hide table
图 2 | g00785185 |
该系统是针对有 3 根地线配置的维修。 |
Show/hide table
图 3 | g00785207 |
该系统是针对有 delta 配置的维修。 |
Show/hide table
图 4 | g00785208 |
该系统是针对有接地阻抗的维修。 |
Show/hide table
图 5 | g00785210 |
该系统是针对有 4 根地线配置的维修。 |
Show/hide table
图 6 | g00785212 |
UPS 接收多路电源。 |
Show/hide table
图 7 | g00785215 |
保养旁通开关 |
Show/hide table
图 8 | g02442538 |
警告旁通开关关闭 |
Show/hide table
图 9 | g00785216 |
输入隔离开关 |
Show/hide table
图 10 | g00785218 |
输出隔离开关 |
Show/hide table
图 11 | g02442139 |
MMU 模块并联连接。 移除输入电源时,该模块的输出处可能留有电压。 |
Show/hide table
图 12 | g02442496 |
MMU 断路开关 |
Show/hide table
图 13 | g02442560 |
MMU 模块并联连接。 维修前,先断开输入和输出开关。 |
Show/hide table
图 14 | g00785222 |
"On"(接通)符号 |
Show/hide table
图 15 | g00785223 |
"Off"(断开)符号 |
Caterpillar Information System:
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Acronyms
C15 Petroleum Engines Exhaust Manifold - Remove and Install
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Wiring Harness (Short Circuit) - Test
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Wiring Harness (Open Circuit) - Test
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Electrical Connector - Inspect
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys System Bypass Operation
Receiving and Unpacking of UPSB505{4480} Receiving and Unpacking of UPSB505{4480}
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Receiving and Handling
2011/02/17 Improved Registration Process for Retrofit Products {1000, 3000, 7000, 7570}
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Information Plate
C15 Petroleum Engines Turbocharger - Install
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Ethernet Interface
3516C and C175-16 Engines Selective Catalytic Reduction Component Location
C6.6 Industrial Engine Flywheel - Install - Equipped with Rear Power Take-Off
C6.6 Industrial Engine Flywheel - Remove - Equipped with Rear Power Take-Off
C13, C15, and C18 Tier 4 Interim Engines Electrical Power Supply - Test
2011/05/16 Improved Software is Now Used for the TH48-E80 Petroleum Transmissions and the SPF343C Pumpers {7620}
2011/02/24 Procedure for Improving Battery Life on Generator Sets {1401}
Assembling and Installing a Selective Catalytic Reduction (SCR) Module for Certain 3516C Generator Sets{1050, 108D, 7279} Assembling and Installing a Selective Catalytic Reduction (SCR) Module for Certain 3516C Generator Sets{1050, 108D, 7279}
C15 Petroleum Engines Engine Oil Filter Base - Remove
C15 Petroleum Engines Engine Oil Filter Base - Install
C15 and C18 Industrial Engines Clean Emissions Module
C15 Petroleum Engines Engine Oil Cooler - Remove
CX31 and CX31 HT On-Highway Transmissions Retarder Operation