CX28 Transmission For Combat and Tactical Vehicles Transmission ; Transfer Case Electronic Control System Caterpillar


Transmission, SPN 746 - FMI 6

Usage:

CX28 TBB
Conditions Which Generate This Code:


Illustration 1g02305055

Schematic of the transfer case differential lock solenoid.

This diagnostic trouble code is associated with the transfer case differential lock solenoid. The FMI "6" means that the ECU has determined that there is a short to ground in the solenoid circuit.

The possible causes of this diagnostic trouble code are listed:

  • The energize circuit of the solenoid is shorted to ground.

  • The solenoid has failed.

  • The ECU has failed. The ECU failing is unlikely.

Note: The following test procedure may create other diagnostic trouble codes. Ignore these created diagnostic trouble codes and clear these diagnostic trouble codes when the original diagnostic trouble code has been corrected. Ensure that the diagnostic trouble code of SPN 746 FMI 6 is active before performing this procedure.

Note: Use a digital multimeter for the measurements in this procedure.

System Response:

The solenoid will not engage.

Test Step 1. CHECK THE SOLENOID.

  1. Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.

  1. Observe the status of the diagnostic trouble code.

  1. Disconnect the solenoid with the active diagnostic trouble code from the machine harness.

Expected Result:

The FMI 6 changes to FMI 5 when the solenoid is disconnected.

Results:

  • YES - The FMI 6 changes to FMI 5 when the solenoid is disconnected. The circuit is correct.

    Repair: The solenoid has failed. Replace the solenoid. Verify that the new solenoid corrects the problem.

    STOP

  • NO - The SPN 746 FMI 6 remains active. Proceed to Test Step 2.

Test Step 2. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO GROUND.

  1. Turn the key start switch and the disconnect switch to the OFF position.

  1. The solenoid remains disconnected from the machine harness.

  1. Disconnect the machine harness connector from the ECU.

  1. At the machine harness connector, measure the resistance from the signal contact J1-62 (wire 705-PK) to all contacts that are used in the machine harness connectors for the ECU.

Expected Result:

Each resistance measurement is greater than 5000 ohms.

Results:

  • OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.

  • NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J1-62 (wire 705-PK) and the circuit with the low resistance measurement.

    Repair: Repair the machine harness or replace the machine harness.

    STOP

Test Step 3. CHECK IF THE DIAGNOSTIC TROUBLE CODE REMAINS.

  1. Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation that is caused by excessive heat, battery acid, or chafing.

  1. Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit.

  1. Reconnect all harness connectors in order to make sure that the connectors are fully seated. Also, make sure that the clips for each connector are fastened.

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Operate the vehicle.

  1. Check the status of the SPN 746 FMI 6.

Expected Result:

The SPN 746 FMI 6 is active.

Results:

  • YES - The SPN 746 FMI 6 is active. The diagnostic trouble code has not been corrected.

    Repair: Check the circuit again. If the Caterpillar Electronic Technician (ET) is available, use the Cat ET service tool in order to perform a "Wiggle Test" on the machine wiring harness. The "Wiggle Test" can detect shorts and opens in the machine wiring harness that are momentary or intermittent. It is unlikely that the ECU has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic trouble code is not found, replace the ECU. Prior to replacing an ECM, always contact your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. See Testing and Adjusting, "Electronic Control Unit - Replace".

    STOP

  • NO - The SPN 746 FMI 6 is not active. The diagnostic trouble code does not exist at this time. The initial diagnostic trouble code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.STOP

Caterpillar Information System:

CX28 Transmission For Combat and Tactical Vehicles Transmission ; Transfer Case Electronic Control System Transmission, SPN 746 - FMI 5
G3520E Generator Set Engines Fuel Control - Test
C15 and C18 Industrial Engines Diesel Particulate Filter
G3520E Generator Set Engines Electrical Power Supply - Test
Instructions to Register the Retrofit and Submit Service Reporting {1000, 3000, 7000, 7570} Instructions to Register the Retrofit and Submit Service Reporting {1000, 3000, 7000, 7570}
G3520E Generator Set Engines Detonation - Test
G3520E Generator Set Engines Cat Data Link - Test
G3520E Generator Set Engines Generator Output Power Readings Do Not Match
G3516 Power Module Additional Messages
G3512E Generator Set Engine Engine Shutdown Occurs Intermittently
G3520E Generator Set Engines Engine Overspeeds
PMG3516 Power Module Methane Gas Detector
CX28 Transmission For Combat and Tactical Vehicles Transmission ; Transfer Case Electronic Control System Transmission, SPN 4045 - FMI 3
CX28 Transmission For Combat and Tactical Vehicles Transmission ; Transfer Case Electronic Control System Transmission, SPN 4046 - FMI 5
CX28 Transmission For Combat and Tactical Vehicles Transmission ; Transfer Case Electronic Control System Transmission, SPN 4046 - FMI 6
CX28 Transmission For Combat and Tactical Vehicles Transmission ; Transfer Case Electronic Control System Transmission, SPN 4045 - FMI 6
CX28 Transmission For Combat and Tactical Vehicles Transmission ; Transfer Case Electronic Control System Transmission, SPN 441 - FMI 16
CX28 Transmission For Combat and Tactical Vehicles Transmission ; Transfer Case Electronic Control System Transmission, SPN 441 - FMI 4
G3520E Generator Set Engines Indicator Lamp - Test
C13, C15, and C18 Tier 4 Final Engines Exhaust Lines (DPF Inlet)
G3512E and G3520E Generator Set Engines Ignition System
C6.6 Industrial Engine Diesel Particulate Filter - Install
C6.6 Industrial Engine Diesel Particulate Filter - Remove
3508C, 3512C and 3516C Locomotive Engines Turbocharger
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.