Hydraulic Tank (Brake, Hoist, Steering) - Remove and Install
拆卸步骤
Show/hide table
车斗降下后,车斗与机架之间没有空隙。 如果不安装固定缆线,可能会导致在此区域作业的人员受伤或死亡。 |
Show/hide table
在工作温度下,液压油箱是热的,而且有压力。 热油和热的部件可能会导致人身伤害。 不要让热油或热的部件与皮肤接触。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才可卸下加注口盖。 慢慢取下加注口盖,让压力释放掉。 |
- 安装车斗固定拉线。 操作和保养手册, "拉线(车斗固定)"。
- 释放系统压力。 请参阅操作和保养手册, "系统压力释放"。
- 将液压油箱中的油排入合适的容器以便保存或废弃这些油。 请参阅操作和保养手册, "液压油箱油位 - 更换 - 举倾和制动系统"。
- 断开软管组件 (1) 。 断开软管组件 (2) 。
Show/hide table
图 1 | g02160022 |
- 拆下卡箍 (3) 。 断开软管 (4) 。 拆下管组件 (5) 。
Show/hide table
图 2 | g02160055 |
- 断开软管组件 (6) 。
Show/hide table
图 3 | g02160090 |
- 断开软管组件 (7) 。
Show/hide table
图 4 | g02160093 |
- 断开软管组件 (8) 。
Show/hide table
图 5 | g02160096 |
- 断开软管组件 (9) 。 拆下管路组件 (10) 。 拆下夹子 (11) 。
Show/hide table
图 6 | g02160066 |
- 拆下软管组件 (12) 。 断开软管组件 (13) 。
Show/hide table
图 7 | g02160074 |
- 拆下夹子 (14) 。 断开软管组件 (15) 。
Show/hide table
图 8 | g02160077 |
- 拆下管组件 (16) 。 断开软管组件 (17) 。 拆下管组件 (18) 。
Show/hide table
图 9 | g02160080 |
- 断开软管组件 (19) 。 断开软管组件 (20) 。 断开软管组件 (21) 。 拆卸管组件 (22) 。
Show/hide table
图 10 | g02160097 |
- 断开软管组件 (23) 。
Show/hide table
图 11 | g02160106 |
- 断开软管组件 (24) 。
Show/hide table
图 12 | g02160174 |
- 拆下卡箍 (25) 。 拆下管组件 (26) 。
Show/hide table
图 13 | g02160193 |
- 拆卸管组件 (27) 。
Show/hide table
图 14 | g02160113 |
- 断开支架 (28) 。 拆下管组件 (29) 。
Show/hide table
图 15 | g02160218 |
Show/hide table
图 16 | g02160224 |
- 拆下夹子 (30) 。 断开线束组件 (31) 。 断开软管组件 (32) 。
Show/hide table
图 17 | g02160326 |
- 将适当的起吊设备固定到液压油箱 (33) 上。 液压油箱 (33) 的重量约为 1270 kg (2800 lb)。
Show/hide table
图 18 | g02160289 |
Show/hide table
图 19 | g02160230 |
- 拆下螺栓 (34) 、盖 (35) 和垫片 (36) 。 对于另一侧,重复本步骤。
- 卸下螺栓 (37) 和垫圈 (38) 。
Show/hide table
图 20 | g02160293 |
- 拆下液压油箱 (33) 。
Show/hide table
图 21 | g02160289 |
安装步骤
- 使用适当的起吊设备以便安装液压油箱 (33) 。 液压油箱 (33) 的重量约为 1270 kg (2800 lb)。
Show/hide table
图 22 | g02160289 |
- 安装垫圈 (38) 和螺栓 (37) 。
Show/hide table
图 23 | g02160293 |
- 安装盖 (35) 和螺栓 (34) 。 此时不要安装垫片 (36) 。
Show/hide table
图 24 | g02160230 |
- 测量鞍座和盖的垂直直径。 测量安装用吊耳的直径。 减去两个测量值,然后记录为尺寸 (X) 。 对于另一侧,重复本步骤。
- 拆下螺栓 (34) 和盖 (35) 。 安装一定数量的尺寸 (X) 加上 0.00 mm (0.000 in),减去 0.12 mm (0.005 in) 的垫片 (36) 。
- 安装盖 (35) 。 安装螺栓 (34) 。 拧紧螺栓 (34) 至扭矩为 900 ± 100 N·m (664 ± 74 lb ft)。 对于另一侧,重复本步骤。
- 连接软管组件 (32) 。 连接线束组件 (31) 。 安装夹子 (30) 。
Show/hide table
图 25 | g02160326 |
- 安装管组件 (29) 。 连接支架 (28) 。
Show/hide table
图 26 | g02160218 |
Show/hide table
图 27 | g02160224 |
- 安装管组件 (27) 。
Show/hide table
图 28 | g02160113 |
- 安装管组件 (26) 。 安装卡箍 (25) 。
Show/hide table
图 29 | g02160193 |
- 连接软管组件 (24) 。
Show/hide table
图 30 | g02160174 |
- 连接软管组件 (23) 。
Show/hide table
图 31 | g02160106 |
- 安装管组件 (22) 。 连接软管组件 (21) 。 连接软管组件 (20) 。 连接软管组件 (19) 。
Show/hide table
图 32 | g02160097 |
- 安装管组件 (18) 。 连接软管组件 (1) 7。 安装管组件 (16) 。
Show/hide table
图 33 | g02160080 |
- 连接软管组件 (15) 。 安装夹子 (14) 。
Show/hide table
图 34 | g02160077 |
- 连接软管组件 (13) 。 安装软管组件 (12) 。
Show/hide table
图 35 | g02160074 |
- 安装夹子 (11) 。 安装管组件 (10) 。 连接软管组件 (9) 。
Show/hide table
图 36 | g02160066 |
- 连接软管组件 (8) 。
Show/hide table
图 37 | g02160096 |
- 连接软管组件 (7) 。
Show/hide table
图 38 | g02160093 |
- 连接软管组件 (6) 。
Show/hide table
图 39 | g02160090 |
- 安装管组件 (5) 。 连接软管 (4) 。 安装卡箍 (3) 。
Show/hide table
图 40 | g02160055 |
- 连接软管组件 (2) 。 连接软管组件 (1) 。
Show/hide table
图 41 | g02160022 |
- 向液压油箱注油。 请参阅操作和保养手册, "液压油箱油位 - 更换 - 举倾和制动系统"。
- 拆下车斗固定拉线。 操作和保养手册, "拉线(车斗固定)"。
Caterpillar Information System:
C27 and C32 Tier 4 Engines Pressure Sensor - Calibrate
C27 and C32 Tier 4 Engines Acceleration Is Poor or Throttle Response Is Poor
Repair of Transmission, Torque Converter, and Torque Divider Shafts {3000, 3063, 3100} Repair of Transmission, Torque Converter, and Torque Divider Shafts {3000, 3063, 3100}
325 VM and VH Variable Gauge Undercarriage Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove and Install
C18 Marine Engine Maintenance Recommendations
C18 Marine Generator Set Maintenance Recommendations
2010/05/31 Improvements Have Been Made to Remanufactured Fuel Injectors on C15 and 3406E Engines {1251, 1290}
2010/06/10 Improvements Have Been Made to Remanufactured Fuel Injectors on C15 and 3406E Engines {1251, 1290}
G3304B and G3306B Engines Catalytic Converter
C27 and C32 Tier 4 Engines Engine Monitoring Parameters
XQ Auto Paralleling General Maintenance Information
C18 Marine Engine Closed Crankcase Ventilation (CCV) Fumes Disposal Filter - Replace
C27 and C32 Tier 4 Engines Injector Solenoid - Test
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Graphic Color Codes
14L Motor Grader Hydraulic and Steering System Ripper Lift Cylinder
C27 and C32 Tier 4 Engines Sensor Signal (PWM) - Test
12M, 140M and 160M Motor Graders Hydraulic and Steering System Blade Lift Cylinder
C15 and C18 Industrial Engines Water Temperature Regulator Housing - Remove and Install
C27 and C32 Tier 4 Engines Electrical Power Supply - Test
3512C SR4B Generator Sets Model View Illustrations
325 VM and VH Variable Gauge Undercarriage Recoil Spring - Disassemble
325 VM and VH Variable Gauge Undercarriage Recoil Spring - Assemble
C27 and C32 Tier 4 Engines Data Link - Test
C175 Generator Sets Battery - Replace