Exhaust Manifold
Show/hide table
| |
| Illustration 1 | g02558316 |
Show/hide table
| |
| Illustration 2 | g02559876 |
|
Tightening sequence | |
Show/hide table
| Specification for 343-0589 Exhaust Manifold Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 12 | 9X-6620 Locknut | Before assembly, apply 4C-5599 Anti-Seize Compound to the threads.
Torque to Refer to Illustration 2 for the locknut tightening procedure. |
| 2 | 12 | 116-3715 Taperlock Stud | Torque tool speed should not exceed 100 rpm.
Torque to |
| 3 | 1 | 324-9290 Bellows As | Assemble the bellows assembly with the “Flow Arrow” toward the NOx Reduction System (NRS) cooler.
The total maximum misalignment of the bellows assembly allowed between the NRS cooler and the exhaust manifold elbow is |
| 4 | 2 | 9N-5085 Clamp | Torque to |
| 5 | 1 | 231-9030 Exhaust Manifold | Before assembly, apply thin coat of 2P-2333 High Temperature Sealer to the outside diameter of the male end of the exhaust manifold.
Remove the excess sealer from the assembled joints. |
| 6 | 6 | 283-2238 Gasket | Install the gasket with tab down as shown in Illustration 1. |
| 7 | 1 | 375-8486 Exhaust Manifold | Before assembly, apply thin coat of 2P-2333 High Temperature Sealer to the inside diameter of the female end of the exhaust manifold.
Remove the excess sealer from the assembled joints. |
| 8 | 4 | 376-3408 Taperlock Stud | Torque tool speed should not exceed 100 rpm.
Torque to |
| 9 | 1 | 350-4503 Exhaust Manifold | Before assembly, apply thin coat of 2P-2333 High Temperature Sealer to the outside diameter of the male end of the exhaust manifold.
Remove the excess sealer from the assembled joints. |
| B | - | - | Angle of the V-band clamp is 45 ± 5 degrees. |
Caterpillar Information System:
C4.4 Industrial Engine Flexible Exhaust Pipe
Clutch Ring Gears For All Power Shift Transmissions {3030, 3155} Clutch Ring Gears For All Power Shift Transmissions {3030, 3155}
C7.1 Industrial Engine Pressure Sensor (DPF) - Remove and Install - Clean Emissions Module
C7.1 Industrial Engine Air Compressor - Remove and Install - Twin Cylinder Compressor
C7.1 Industrial Engine Air Compressor - Remove and Install - Single Cylinder
C7.1 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "A"
C7.1 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "B"
C4.4 Industrial Engine Crankshaft
349F and 352F Excavators Machine System Pilot Valve (Swing Parking Brake)
3500 Petroleum Engines and Petroleum Generator Sets Safety Messages
C15 Generator Sets Generator Start-up Checklist
C4.4 Industrial Engine Crankshaft Pulley
2010/05/19 New High Temperature Hardware Is Available for Exhaust Elbow Support Brackets on 3508B and 3512B Locomotive Engines {1059, 1061}
349F and 352F Excavators Bucket - Remove and Install
C7.1 Industrial Engine and Generator Set Engine Vibration Is Excessive
Individual Clutch Modulation (ICM) Control Valves{3065, 3139} Individual Clutch Modulation (ICM) Control Valves{3065, 3139}
C27 and C32 Tier 4 Engines Coolant Level - Test
C27 and C32 Tier 4 Engines Data Link Configuration Status - Test
G3516 TA Engine Gas Pressure
G3500B Engines Gas Pressure Regulator
C18 Marine Engine Safety Messages
C27 and C32 Tier 4 Engines Fuel Filter Differential Pressure - Test
3176C and 3196 Marine Engines Fire Prevention and Explosion Prevention
C18 Marine Engine Engine Electronics