Generator Start-up Checklist
Show/hide table
GENERATOR START-UP CHECKLIST | ||||||||
---|---|---|---|---|---|---|---|---|
RATING INFORMATION | ||||||||
Engine Serial Number: ___________________________________ | Arrangement Number: ___________________ | |||||||
Generator Serial Number: _________________________________ | Arrangement Number: ___________________ | |||||||
GENERATOR NAME PLATE INFORMATION | ||||||||
Voltage: ___________________ | Package (prime, continuous, standby): _________________ | |||||||
Amperage: _________________ | Kilowatts: ________________________________________ | |||||||
Storage Location: | ||||||||
Main Stator Megohmmeter Reading: | Before Storage: | After Storage: | ||||||
Generator dried for 24 hours prior to start-up? | (Y/N) | Drying method: | ||||||
SPACE HEATERS | Yes | No | Comments | |||||
Space heaters operating properly? | ||||||||
Space heater operated 48 hours. before start-up? | ||||||||
MEGOHMMETER TEST (SEHS9124) | 30 sec. reading | 60 sec. reading | 30 sec. corrected | 60 sec. corrected | Ambient temp. | Comments | ||
Beginning of Storage | Main Stator | |||||||
Main Rotor | ||||||||
Exciter Stator | ||||||||
Exciter Rotor | ||||||||
PMG Stator | ||||||||
Start-up | Main Stator | |||||||
Main Rotor | ||||||||
Exciter Stator | ||||||||
Exciter Rotor | ||||||||
PMG Stator |
Show/hide table
GENERATOR START-UP CHECKLIST (CONT.) | ||||||||
---|---|---|---|---|---|---|---|---|
No Load | Regulator VR6 | Voltage | Amps | Comments | ||||
E- to E+ | DC | |||||||
20 to 22 | AC | |||||||
Self-Excited
20 to 22 |
AC | |||||||
Permanent Magnet Excited
26 to 28 |
AC | |||||||
Permanent Magnet Excited
28 to 30 |
AC | |||||||
Permanent Magnet Excited
26 to 30 |
AC | |||||||
AREP
26 to 28 |
AC | |||||||
AREP
28 to 30 |
AC | |||||||
Full Load | Regulator VR6 | Voltage | Amps | Comments | ||||
E- to E+ | DC | |||||||
20 to 22 | AC | |||||||
Self-Excited
20 to 22 |
AC | |||||||
Permanent Magnet Excited
26 to 28 |
AC | |||||||
Permanent Magnet Excited
28 to 30 |
AC | |||||||
Permanent Magnet Excited
26 to 30 |
AC | |||||||
AREP
26 to 28 |
AC | |||||||
AREP
28 to 30 |
AC |
Show/hide table
GENERATOR START-UP CHECKLIST (CONT.) | ||||||||
ELECTRICAL | Yes | No | Comments | |||||
Unit properly grounded | ||||||||
Check diodes | ||||||||
Over current protection | ||||||||
Over voltage protection | ||||||||
Check for loose wiring | ||||||||
Adjust voltage | ||||||||
Adjust frequency | ||||||||
MECHANICAL | Data | Comments | ||||||
Bearing temperature readings at full load | Front __________ Rear ___________ | |||||||
Stator temperature readings at full load | A0 _______ B0 _______ C0 _______ | |||||||
Air gap on main stator | Top __________ Bottom __________ | |||||||
Air gap on exciter stator | Top __________ Bottom __________ | |||||||
Air gap of PMG | Top __________ Bottom __________ | |||||||
Ambient air to generator at full load | Temperature ____________________ | |||||||
Supplier air opening to generator | Size of Opening _________________ | |||||||
SWITCH GEAR/PARALLEL OPERATION | ||||||||
Manufacturer: | ||||||||
Setting 1 | Setting 2 | Setting 3 | Comments | |||||
Circuit breaker type | ||||||||
Overload setting | ||||||||
Reverse power relay | ||||||||
VAR/PF Controller | ||||||||
Load share | ||||||||
INSTALLATION & LOAD INFORMATION | ||||||||
Neutral grounding system | UPS | |||||||
Enclosure type | - Size | |||||||
Motor: | Other loads: | |||||||
- Total SKVA | - Lighting | |||||||
- Total HP | - Computers | |||||||
- Welding | ||||||||
- Non-linear | ||||||||
- Other | ||||||||
FULL LOAD DATA | ||||||||
Voltage | Amps | KW | KVARS | P.F. | ||||
Caterpillar Information System:
C4.4 Industrial Engine Crankshaft Pulley
Cleaning Procedure After a Pump, Motor, or Cylinder Failure for Backhoe Loaders{5050, 7000} Cleaning Procedure After a Pump, Motor, or Cylinder Failure for Backhoe Loaders{5050, 7000}
C7.1 Industrial Engine Fuel Priming Pump - Remove and Install - Electric Fuel Lift Pump (EFLP)
C7.1 Industrial Engine Water Temperature Regulator - Remove and Install
C7.1 Industrial Engine Water Pump - Remove
C7.1 Industrial Engine Water Pump - Install
C7.1 Industrial Engine Wastegate Solenoid - Remove and Install
C7.1 Industrial Engine Vibration Damper and Pulley - Remove
C7.1 Industrial Engine Vibration Damper and Pulley - Install
C7.1 Industrial Engine Valve Mechanism Cover - Remove and Install
C7.1 Industrial Engine Turbocharger - Remove - Second Stage Turbocharger
C7.1 Industrial Engine Turbocharger - Install - Second Stage Turbocharger
3500 Petroleum Engines and Petroleum Generator Sets Safety Messages
349F and 352F Excavators Machine System Pilot Valve (Swing Parking Brake)
C4.4 Industrial Engine Crankshaft
C7.1 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "B"
C7.1 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "A"
C7.1 Industrial Engine Air Compressor - Remove and Install - Single Cylinder
C7.1 Industrial Engine Air Compressor - Remove and Install - Twin Cylinder Compressor
C7.1 Industrial Engine Pressure Sensor (DPF) - Remove and Install - Clean Emissions Module
Clutch Ring Gears For All Power Shift Transmissions {3030, 3155} Clutch Ring Gears For All Power Shift Transmissions {3030, 3155}
C4.4 Industrial Engine Flexible Exhaust Pipe
C9.3 Tier 4 Final Engines Exhaust Manifold
2010/05/19 New High Temperature Hardware Is Available for Exhaust Elbow Support Brackets on 3508B and 3512B Locomotive Engines {1059, 1061}