CX31-P600 Petroleum Transmission Caterpillar


Torque Converter

Usage:

CX31-P600 GFY

表 1
变矩器 
零件号  发动机  hp 
288-2659  C9 到 C13  小于 400 
288-2661  C9 到 C13  大于 400 
288-2676  C15   


图 1g01821373
前视图


图 2g01759556
典型实例
剖面 A-A

(1) 44 个螺栓的扭矩 ... 60 ± 7 N·m (44 ± 5 lb ft)



图 3g01821376
典型实例
剖面 B-B

(2) 六个螺栓的扭矩 ... 30 ± 5 N·m (22 ± 4 lb ft)

(3) 螺塞的扭矩 ... 285 ± 15 N·m (210 ± 11 lb ft)

(4) 螺栓的扭矩 ... 285 ± 15 N·m (210 ± 11 lb ft)

注: 在将 O 形密封圈安装到槽中后,使用清洁的变速箱油润滑 O 形密封圈 (6),然后再将先导 (5) 组装到离合器壳体组件 (7) 的孔中。

注: 在将密封圈安装到槽中后,使用清洁的变速箱油润滑两个密封圈 (9),然后再将活塞 (8) 组装到离合器壳体组件 (7) 的孔中。

(10) 288-2661288-2676 变矩器的两个新摩擦盘和两个新板的厚度为 12.24 ± 0.30 mm (0.482 ± 0.012 in)

275-5308 摩擦盘

数量 ... 2
1 块摩擦盘的厚度 ... 3.81 ± 0.10 mm (0.150 ± 0.004 in)

260-9557

数量 ... 2
1 片板的厚度 ... 2.31 ± 0.05 mm (0.091 ± 0.002 in)

(10) 288-2659 变矩器的一个新摩擦盘和一个新板的厚度为 6.12 ± 0.15 mm (0.241 ± 0.006 in)

275-5308 摩擦盘

数量 ... 1
1 块摩擦盘的厚度 ... 3.81 ± 0.10 mm (0.150 ± 0.004 in)

260-9557

数量 ... 1
1 片板的厚度 ... 2.31 ± 0.05 mm (0.091 ± 0.002 in)

(11) 八根螺栓的扭矩 ... 105 ± 14 N·m (77 ± 10 lb ft)



图 4g02016554
C-C 部分
(F) 37 ± 0.5 mm (1.46 ± 0.02 in)

注: 请参阅图 4 以便将两个定位销 (12) 组装到变矩器叶轮 (13) 上要求的高度。



图 5g01821375
截面 D-D

注: 组装自由轮弹簧 (13),使尽量多的簧圈朝向外侧。

(14) 1T-0680 自由轮弹簧

数量 ... 11
在测试力下的长度 ... 5.6 mm (0.22 in)
测试力 ... 6.7 至 11.1 N (1.5 至 2.5 lb)
测试后的自由长度 ... 9.1 mm (0.36 in)
宽度 ... 9.1 ± 0.5 mm (0.36 ± 0.02 in)


图 6g01821414
局部放大图 E
耦合组件

(15) 12 根螺栓的扭矩 ... 50 ± 10 N·m (37 ± 7 lb ft)

Caterpillar Information System:

770 and 772 Off-Highway Truck Parking
C175-16 Marine Engines Fuel System Primary Filter - Clean/Inspect/Replace
3508B, 3512B, and 3516B High Displacement Generator Sets Rotating Rectifier - Inspect/Test
C15 and C18 Petroleum Generator Sets Space Heater - Test
2009/10/15 New Software is Now Used for the Product Link PL121SR and PL321SR Systems {7606, 7620}
G3512E and G3520E Generator Set Engines Engine Speed/Timing Sensor
C18 Marine Engines Sensors and Electrical Connectors
G3512E and G3520E Generator Set Engines Circuit Breaker
G3512 Generator Set Engines Power Supply
3508, 3512 and 3516 Generator Set Engines Aftercooler - Remove and Install
C32 Petroleum Generator Sets Declaration of Conformity
C32 Petroleum Generator Sets Sound Information
3508B, 3512B, and 3516B High Displacement Generator Sets Stator Winding Temperature - Test
3512C HD SR500 Generator Sets Sound Information
3516C HD Generator Set with Gearbox Declaration of Conformity
C7.1 Industrial Engine and Generator Set Motorized Valve - Test
2009/10/23 Improved Assembly for the Alternator Bracket on 3054C, 3054E and C4.4Engines {1405}
2009/12/03 Gasket for the Turbocharger and Exhaust Manifold for 3056, 3056E and C6.6 Engines {1052, 7555}
C13 Industrial Engines Engine Oil Filter Base
797F and 797F XQ Off-Highway Truck/Tractor Braking System Gear Motor (Rear Axle Oil Cooler Fan)
793F Off-Highway Truck Machine Systems Transmission Control - Remove and Install
PM3516 Power Modules Sound Information
PM3516 Power Modules Declaration of Conformity
PM3516 Power Modules Generator Set Installation
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.