797F and 797F XQ Off-Highway Truck/Tractor Braking System Caterpillar


Brake Accumulator System Recovery - Test

Usage:

797F LAJ



图 1g02128033

典型视图

注: 应通过 Cat 电子技师检查制动系统压力。

------ WARNING! ------

机器突然移动,会造成人员伤亡。

机器突然移动或释放气压或油压,可能对机器上或机器附近的人员造成伤害。

在测试和调整任何空气系统或液压系统之前,为防止可能的伤害,执行测试和调整, "概述"部分的程序。



注意

在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。

有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。

按照当地法规和要求处置所有液体。


注: 执行该测试前,执行测试和调整, "制动系统压力 - 测试和调整"中的测试。 当机器挂档时,此测试将检查后部测试端口上的停车制动器压力。

  1. 起动发动机。 使制动器蓄能器完全充注。

  1. 以低怠速运转发动机。 由于系统泄漏和润滑,制动蓄能器中的压力将会下降。 电磁阀控制制动蓄能器的充注循环。 执行任何测量前,使制动蓄能器充注循环至少发生十次。

    注: 记录在切入压力和切断压力时的读数。

  1. 执行测试前,必须满足下列所有条件:

    • 车轮必须楔住。

    • 变速箱必须处于停车位置。

    • 发动机需要在低怠速下运转。

    • 阀体位置操纵杆必须处于保持位置。

    注: 当满足以上所有条件时,可以开始测试。

    注: 执行所有测试前请先通读下一步。

  1. 在一个稳定的运动中,当发动机低怠速运转时,完全应用行车制动器,并将变速箱挂上档。

  1. 在 30 秒后,将变速箱操纵杆换入停车档。

  1. 在制动系统开始恢复压力前,找到曾达到的最低压力。 此外,检查重新充注蓄能器或者从接通压力到切断压力所需的时间。 蓄能器恢复所需的时间应不超过 12 秒。

    恢复时间过长的可能原因是电磁阀(卸载阀)或分流器阀(卸载阀)有故障或系统泄漏。 泵也可能有故障。

    制动系统最低压力应为 9500 kPa (1380 psi)。 低制动系统压力可能表示电磁阀(卸载阀)或分流器阀(卸载阀)有故障,控制阀(制动器)内部泄漏,或者机油通过停车制动器释放泵漏回。

  1. 停止发动机。

    注: 执行测试和调整, "松紧调节器 - 测试和调整",以确定每个车轮处的压力。

Caterpillar Information System:

797F and 797F XQ Off-Highway Truck/Tractor Braking System Relief Valve (Main) - Test and Adjust
CX31-P600 Petroleum Transmission Drive Plate - Flywheel) (C15 - C18 Engines
C13 Industrial Engines Camshaft
349F and 352F Excavators Hydraulic System Pump Control (Negative Flow) - Adjust
797F and 797F XQ Off-Highway Trucks Torque Converter Sump Oil Level - Check
325D and 329D Excavators Hydraulic System Swing Bearing Movement - Measure
CX31-P600 Petroleum Transmission Coupling Fastener - Flywheel) (C9 - C13 Engines
797F and 797F XQ Off-Highway Trucks Torque Converter and Transmission Oil Sample - Obtain
349F and 352F Excavators Hydraulic System Accumulator (Pilot) - Test and Charge
797F and 797F XQ Off-Highway Truck/Tractor Braking System Motor Rotating Group (Brake Cooling) - Adjust
793F Off-Highway Truck Machine Systems Traction Control Valve - Assemble
G3512E and G3520E Generator Set Engines Integrated Temperature Sensing Module
2009/11/18 Changes To Caterpillar Incident Reporting Field Use Form And DSN Incident Report Entry Screens {1000, 7000}
CX31-P600 Petroleum Transmission Drive Plate - Flywheel) (C9 - C13 Engines
797F and 797F XQ Off-Highway Truck/Tractor Braking System Parking Brake Release Pressure - Test
CX31-P600 Petroleum Transmission Torque Converter Housing - Integral Pump Drive, Retarder
C13 and C15 On-highway Engines Fuel System Pressure - Test
C32 Petroleum Generator Sets Sound Information
C32 Petroleum Generator Sets Declaration of Conformity
3508, 3512 and 3516 Generator Set Engines Aftercooler - Remove and Install
G3512 Generator Set Engines Power Supply
G3512E and G3520E Generator Set Engines Circuit Breaker
C18 Marine Engines Sensors and Electrical Connectors
G3512E and G3520E Generator Set Engines Engine Speed/Timing Sensor
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.