C7.1 Industrial Engine and Generator Set Caterpillar


Exhaust Has Excessive White Smoke

Usage:

C7.1 770
Note: Some white smoke may be present during cold start-up conditions and during acceleration after a prolonged period at low idle. If the white smoke persists, there may be a fault.

Probable Causes

  • Diagnostic codes

  • Coolant temperature sensor circuit

  • Low coolant temperature

  • Cooling system

  • Glow plugs

  • Ether Injection

  • Fuel quality

  • Valve lash

  • Low compression (cylinder pressure)

  • Individual malfunctioning cylinder

Recommended Actions

Diagnostic Codes

Use one of the following methods to check for active diagnostic codes:

  • The electronic service tool

  • The display on the control panel

  • Flash Codes

Electronic Service Tool

  1. Connect the electronic service tool to the diagnostic connector.

  2. Check for active diagnostic codes on the electronic service tool.

  3. Investigate any active codes before continuing with this procedure. Refer to Troubleshooting, "Troubleshooting with a Diagnostic Code".

Display on the Control Panel

Note: The following procedure is only applicable if the application is equipped with a display on the control panel.

  1. Check the display on the control panel for active diagnostic codes.

  2. Troubleshoot any active codes before continuing with this procedure. Refer to Troubleshooting, "Troubleshooting with a Diagnostic Code".

Flash Codes

Note: The following procedure is only applicable if the machine is equipped with the appropriate warning lamps.

  1. Check the warning lamps on the control panel for flash codes. Flash codes are explained in Troubleshooting, "Flash Codes".

  2. If any flash codes are displayed, troubleshoot the codes before continuing with this procedure. Refer to Troubleshooting, "Troubleshooting with a Diagnostic Code".

Coolant Temperature Sensor Circuit

  1. Connect the electronic service tool to the diagnostic connector.

  2. Monitor the display screen on the electronic service tool in order to verify the presence of active diagnostic codes for the coolant temperature. Refer to Troubleshooting, "Engine Temperature Sensor Open or Short Circuit - Test".

  3. If the fault has not been eliminated, proceed to "Low Coolant Temperature".

Low Coolant Temperature

Check that the water temperature regulator is operating correctly. Refer to Systems Operation, Testing, and Adjusting, "Water Temperature Regulator - Test".

If the water temperature regulator is operating correctly, proceed to "Glow Plugs".

Cooling System

Check for an internal coolant leak into the cylinder and/or the exhaust. Refer to Systems Operation/Testing and Adjusting, "Cooling System".

Note: Check for leakage at the ARD nozzle heater o-rings. If the o-rings are leaking coolant, replace the ARD head.

Glow Plugs

Note: Faulty glow plugs will only affect the production of white smoke when the ambient temperature is between 5° C (41° F) and −25° C (−13° F).

  1. Check for correct operation of the glow plugs. Refer to Troubleshooting, "Glow Plug Starting Aid - Test".

  2. If necessary, replace faulty glow plugs. Refer to Disassembly and Assembly, "Glow Plug - Remove and Install".

  3. If the repairs do not eliminate the fault, proceed to "Ether Injection".

Ether Injection

Note: A faulty ether starting aid will only affect the production of white smoke when the ambient temperature is below −25° C (−13° F).

  1. Use the electronic service tool to test the ether starting aid.

  2. If the ether starting aid is faulty, test the system. Refer to Troubleshooting, "Ether Starting Aid - Test".

  3. If necessary, perform any repairs to the ether starting aid.

  4. If the repairs do not eliminate the fault, proceed to "Fuel Quality".

Fuel Quality

  1. Check the diesel fuel for quality. Refer to Systems Operation, Testing, and Adjusting, "Fuel Quality - Test".

    Note: Diesel fuel with a low cetane value is likely to cause white smoke.

  2. If the repair does not eliminate the fault, proceed to "Valve Lash".

Valve Lash

  1. Ensure that the valve lash is correct. Refer to Systems Operation, Testing, and Adjusting, "Engine Valve Lash - Inspect".

  2. If the repair does not eliminate the fault, proceed to "Low Compression (cylinder pressure)".

Low Compression (cylinder pressure)

  1. Perform a compression test. Refer to Systems Operation, Testing, and Adjusting, "Compression - Test ".

  2. If low compression is noted on any cylinders, investigate the cause and rectify the cause.

    Possible causes of low compression are shown in the following list:

    • Loose glow plugs

    • Faulty piston

    • Faulty piston rings

    • Worn cylinder bores

    • Worn valves

    • Faulty cylinder head gasket

    • Damaged cylinder head

  3. Perform all necessary repairs.

  4. Ensure that the repair has eliminated the fault.

  5. If the repair does not eliminate the fault, proceed to "Individual Malfunctioning Cylinder".

Individual Malfunctioning Cylinder

  1. With the engine speed at a fast idle, use the electronic service tool to perform the manual "Cylinder Cut Out Test". As each cylinder is cut out, listen for a change in the sound from the engine. When a cylinder is cut out, there should be a noticeable change in the sound of the engine. If a change in the sound of the engine is not noted, the isolated cylinder is not operating under normal conditions. If the isolation of a cylinder causes a change in the sound that is less noticeable, the cylinder may be operating below normal performance. Investigate the cause of the fault on any cylinder that is not operating. Investigate the cause of the fault on any cylinder that is operating below normal performance.

  2. Rectify any faults.

  3. If the fault has not been eliminated, contact the technical communicator at a Caterpillar dealer.

Caterpillar Information System:

CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission MID 027 - CID 0190 - FMI 08
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission MID 027 - CID 0190 - FMI 02
G3304B and G3306B Engines Engine Oil Pump - Install
2009/07/01 A New Unloader Kit Is Now Used {1803}
G3304B and G3306B Engines Engine Oil Pump - Remove
3508C, 3512C, and 3516C Locomotive Engines Speed Control - Test
XQ175 Rental Generator Set Single Unit Operation
3500 Engine Emissions Upgrade Groups{1000, 775E} 3500 Engine Emissions Upgrade Groups{1000, 775E}
C18 Marine Engines Product Description
C7.1 Industrial Engine and Generator Set Fuel Consumption Is Excessive
Identification and Applications of Transmission Clutch Plates and Specifications to Machine Reaction Faces for Power Shift Transmissions {3054, 3155, 3160, 3190} Identification and Applications of Transmission Clutch Plates and Specifications to Machine Reaction Faces for Power Shift Transmissions {3054, 3155, 3160, 3190}
C7.1 Industrial Engine and Generator Set Oil Consumption Is Excessive
C7.1 Industrial Engine and Generator Set Inlet Air Temperature Is High
3304B and 3306B Engines for Caterpillar Built Machines Engine Oil Pump - Disassemble
2009/06/15 New Fasteners for the Valve Mechanism Cover {1107, 1120}
C7.1 Industrial Engine and Generator Set Power Is Intermittently Low or Power Cutout Is Intermittent
C7.1 Industrial Engine and Generator Set Acceleration Is Poor or Throttle Response Is Poor
C13 and C15 On-highway Engines Diesel Particulate Filter Has High Ash Load
C7.1 Industrial Engine Fuel Manifold (ARD) - Aftertreatment Regeneration Device
C7.1 Industrial Engine Exhaust Combustion (ARD) - Aftertreatment Regeneration Device
C15 and C18 Tier 4 Final Engines General Information
3508C, 3512C, and 3516C Locomotive Engines Sensor Supply - Test
C7.1 Industrial Engine Electronic Control Wiring Group - Aftertreatment Regeneration Device
2009/08/24 An Improved Camshaft Is Used for G3520C Generator Sets that Are Rated at 1800 rpm {1210}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.