Temperature Sensor (DPF) - Remove and Install - Clean Emissions Module
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | -     | Loctite 771 抗咬合剂     | -     |
- 将燃油供应转到 OFF 位置,并将电源断路开关转到 OFF 位置。
- 将冷却液从冷却系统中排入合适的容器,以便保存或弃置。 请参考操作和保养手册, "冷却系统冷却液 - 更换"。
- 拆下螺栓 (1) 。
Show/hide table
图 1 | g02201253 |
这是机器左侧的发动机室视图。 |
Show/hide table
图 2 | g02201257 |
- 断开管组件 (2) 、 (3) 、 (4) 和 (5) 。
注: 盖住断开的所有管组件和接头,以防油液损失。 这也能避免系统受到污染。
- 断开管组件 (6) 、 (7) 和 (8) 。
Show/hide table
图 3 | g02201258 |
注: 盖住断开的所有管组件和接头,以防油液损失。 这也能避免系统受到污染。
- 将管组件作为一体缓慢从机器右侧拆下。
- 拆下电缆带后拆下火焰探测温度传感器 (9) 。
Show/hide table
图 4 | g02199957 |
注: 在所有电缆带位置和所有保温层上做好方位和位置标记,以便于安装。
- 断开固定到火焰探测温度传感器 (10) 上的线束组件。 拆下用来固定传感器的所有电缆带。
Show/hide table
图 5 | g02201433 |
注: 在所有电缆带位置和所有保温层上做好方位和位置标记,以便于安装。
- 拆下进口温度传感器 (11) 。
Show/hide table
图 6 | g02201534 |
注: 在所有电缆带位置和所有保温层上做好方位和位置标记,以便于安装。
安装步骤
- 按相反顺序安装火焰探测温度传感器。
- 将工具 (A) 涂抹到火焰探测温度传感器 (9) 和进口温度传感器 (11) 的螺纹上。 将火焰探测温度传感器 (9) 和进口温度传感器 (11) 上紧到 45 ± 5 N·m (33 ± 4 lb ft) 的扭矩。
- 将管组件 (8) 上紧到 16 ± 2 N·m (142 ± 18 lb in) 的扭矩。
- 拧紧管组件 (6) 至扭矩为 11 ± 2 N·m (97 ± 18 lb in)。
- 拧紧管组件 (7) 至扭矩为 16 ± 2 N·m (142 ± 18 lb in)。
- 拧紧管组件 (5) 至扭矩为 20 ± 2 N·m (177 ± 18 lb in)。
- 拧紧管组件 (4) 至扭矩为 16 ± 2 N·m (142 ± 18 lb in)。
- 将管组件 (3) 上紧到 43 ± 4 N·m (32 ± 3 lb ft) 的扭矩。
- 拧紧管组件 (2) 至扭矩为 27 ± 3 N·m (239 ± 27 lb in)。
Caterpillar Information System:
C175 Generator Sets System Pressure Release
C7 Engine for Combat and Tactical Vehicles Air Compressor Drive Gear - Install
C7 Engine for Combat and Tactical Vehicles Air Compressor Drive Gear - Remove
C7 Engine for Combat and Tactical Vehicles Air Compressor - Remove and Install
C7 Engine for Combat and Tactical Vehicles Electric Starting Motor - Remove and Install
C7 Engine for Combat and Tactical Vehicles Alternator - Remove and Install
C7 Engine for Combat and Tactical Vehicles Engine Control Module - Remove and Install
C7 Engine for Combat and Tactical Vehicles Fan Drive Mounting Group - Remove and Install
C7 Engine for Combat and Tactical Vehicles Inlet Air Temperature Sensor - Remove and Install
C7 Engine for Combat and Tactical Vehicles Boost Pressure Sensor - Remove and Install
C7 Engine for Combat and Tactical Vehicles Speed/Timing Sensor - Remove and Install
C7 Engine for Combat and Tactical Vehicles Injection Actuation Pressure Sensor - Remove and Install
C13, C15, and C18 Tier 4 Interim Engines ECM - Replace
2009/04/27 Proper Long Term Storage of Caterpillar Products {0355, 1000, 7000}
C7.1 Industrial Engine Electrical System
C15 and C18 Industrial Engines Pressure Sensor (DPF) - Remove and Install
Adjustment of Overload Protection for Generators{4450, 4493} Adjustment of Overload Protection for Generators{4450, 4493}
3500B and 3500C Marine Engines Alternator and Regulator
C13, C15, and C18 Generator Set Engines Belt Tightener
120 and 120 AWD Motor Grader Ether Starting Aid Cylinder - Replace
C9.3 Engines for Caterpillar Built Machines Customer Passwords
795F AC and 795F AC XQ Off-Highway Trucks Air Filter Element (Inverter Cabinet) - Check
2009/04/27 An Improved Rod for the Recoil Spring is Now Used {4158}
2009/04/20 How Is Service Information Accessed / Used {0374, 1000, 7000}