Vibration Damper and Pulley - Remove and Install
- Remove belt guard (1).
Show/hide table
Illustration 2 g01608133 - Remove V-belt (2) from pulley (4). Refer to Operation and Maintenance Manual, "Alternator Belt - Inspect/Adjust/Replace".
- Remove nuts (5) and pulley (4).
- Slide vibration damper (3) along studs (6). Attach a suitable lifting device to vibration damper (3). The weight of vibration damper (3) is approximately
50 kg (110 lb) . Remove vibration damper (3) from studs (6). - Remove studs (6), if necessary.
- Attach a suitable lifting device to damper adapter (8), if necessary. The weight of damper adapter (8) is approximately
23 kg (50 lb) . Remove bolts (7) and damper adapter (8).
Show/hide table
Illustration 1 | g01608113 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 452-6006 | Grease | - |
Show/hide table
NOTICE |
---|
Thoroughly inspect the viscous damper for signs of leakage or for signs of a dented (damaged) case. Either of these conditions can cause the weight to make contact with the case. This can affect the viscous damper's operation. |
- Attach a suitable lifting device to damper adapter (8), if necessary. The weight of damper adapter (8) is approximately
23 kg (50 lb) . - Apply Tooling (A) to bolts (7). Install damper adapter (8) and bolts (7).
- Install studs (6), if necessary. Tighten studs (6) to a torque of
65 ± 10 N·m (48 ± 7 lb ft) . - Attach a suitable lifting device to vibration damper (3). The weight of vibration damper (3) is approximately
50 kg (110 lb) . Install vibration damper (3) on studs (6). - Install pulley (4) and nuts (5). Tighten nuts (5) to a torque of
135 ± 20 N·m (100 ± 15 lb ft) . - Install V-belt (2) on pulley (4). Refer to Operation and Maintenance Manual, "Alternator Belt - Inspect/Adjust/Replace".
Show/hide table
Illustration 4 g01608113 - Install belt guard (1).
Show/hide table
Illustration 3 | g01608133 |
Caterpillar Information System:
2008/09/08 Procedure for Crankshafts that will not Rotate after Installation during a Rebuild {1000, 1202}
TH48-E80 Oil/Gas Transmission Torque Converter - Install
3508C, 3512C and 3516C Locomotive Engines Prelube Pressure Switch
TH48-E80 Oil/Gas Transmission Torque Converter - Remove
C27 and C32 Industrial and Petroleum Engines Engine Oil Pan
C27 and C32 Industrial and Petroleum Engines Engine Oil Pan
C27 and C32 Industrial and Petroleum Engines Engine Oil Pan
3512C Engine and 785D Off-Highway Truck/Tractors ECM - Replace
3512C Petroleum Engines Intake Manifold Air Temperature Is High
3512B and 3516B Engines Piston and Rings - Two-Piece Piston
C18 Generator set and C18 Marine Engines Aftercooler - Install
C18 Generator set and C18 Marine Engines Aftercooler - Remove
2009/04/20 An Improved Radio Power Converter is used on Excavators. {1408, 1421, 7338}
C27 and C32 Industrial and Petroleum Engines Vibration Damper and Pulley
3500B Locomotive Engines Cylinder Head Valves
3512B Generator Set Engine Pressure Contactor
3512B Generator Set Engine Pressure Transducer
Specifications for Inspection of Driveline Fasteners {3030, 3101, 3159, 3253, 3258, 3278, 4050} Specifications for Inspection of Driveline Fasteners {3030, 3101, 3159, 3253, 3258, 3278, 4050}
G3412C, G3508, G3512 and G3516 Engines Status Control Module General Information
G3412C, G3508, G3512 and G3516 Engines Status Control Module Service Tools
G3412C, G3508, G3512 and G3516 Engines Status Control Module Symptom Troubleshooting
G3412C, G3508, G3512 and G3516 Engines Status Control Module Engine Cranks but Does Not Start
320 Variable Gauge OEM Undercarriage Machine System Specifications Travel Motor Lines
3512B Generator Set Engine Thermocouple