Housing (Front) - Remove
Start By:
- Remove the speed/timing sensor. Refer to Disassembly and Assembly, "Speed/Timing Sensor - Remove and Install".
- Remove the fan drive, if necessary. Refer to Disassembly and Assembly, "Fan Drive - Remove".
- Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install".
- Remove the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector Hydraulic Pump - Remove".
- Remove the auxiliary water pump, if necessary. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Remove".
- Remove the air compressor, if necessary. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install".
- Remove the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Remove".
- Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bolts (1) that fasten front housing (3) to the cylinder block.
- Remove bolts (2) that fasten the engine oil pan to the front housing.
- Remove front housing (3) from the cylinder block.
Note: If necessary, hit the front housing with a soft faced hammer in order to separate the front housing from the cylinder block.
Show/hide table
| |
| Illustration 1 | g01146329 |
Caterpillar Information System:
C175-16 and C175-20 Generator Set Engines Engine Oil Pan
C175-16 and C175-20 Generator Set Engines Engine Oil Pan
C4.4 and C6.6 Engines for Caterpillar Built Machines Electrical Connectors - Inspect
2008/03/17 A New Bearing Block within the Governor is Now Used {1000}
C7 PETROLEUM Petroleum Engine Crankshaft Rear Seal - Install
C7 PETROLEUM Petroleum Engine Water Temperature Regulator - Remove and Install
C175-16 and C175-20 Generator Set Engines Cylinder Head Valves
345D, 349D and 349D2 Excavator Machine System Specifications Hydraulic Oil Cooler Lines Group
345D, 349D and 349D2 Excavator Machine System Specifications Swing Motor Lines
C13, C15, and C18 Tier 4 Final Engines Speed/Timing Sensor
C7 PETROLEUM Petroleum Engine Engine Oil Pump - Assemble
Identification of Non-Metallic Discs that are Used in Power Shift Transmissions {3030, 3155} Identification of Non-Metallic Discs that are Used in Power Shift Transmissions {3030, 3155}
C7 PETROLEUM Petroleum Engine Housing (Front) - Install
2008/04/14 Increased Support for Repair Parts is Available for Products that are sold by Dealer Service Tools from Advanced Technology Services {0599}
2008/03/17 Updated Instruction For The Bypass Harness {0785, 1408}
Transmission Clutch Plates and Disc Assemblies with Rayflex Friction Material {3030, 3155, 3190} Transmission Clutch Plates and Disc Assemblies with Rayflex Friction Material {3030, 3155, 3190}
C7 PETROLEUM Petroleum Engine Valve Mechanism Cover - Remove and Install
Information on the Clean Gas Induction (CGI) Flex Pipe Connection Found Broken in Some 2007 Emissions Compliant Engines{1071, 108N, 5510} Information on the Clean Gas Induction (CGI) Flex Pipe Connection Found Broken in Some 2007 Emissions Compliant Engines{1071, 108N, 5510}
345D, 349D and 349D2 Excavator Machine System Specifications Main Hydraulic Pump Mounting
3516C Locomotive Engine Configuration Parameters
C175-16 and C175-20 Generator Set Engines Air Lines
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine System Pilot Lines - Joystick
3516C Locomotive Engine Maintenance Interval Schedule
C175-16 and C175-20 Generator Set Engines Air Lines