2007/12/17 Caterpillar

Correction to Operation and Maintenance Manual , "Steering Frame Lock" {7506}

Usage:

R1700G SBR

Load Haul Dump: R1700G (S/N: SBR591-UP)

Operation and Maintenance Manual, SEBU8211, "R1700G Load Haul Dump", "Steering Frame Lock". This manual is part of Service Manual, KENR6258 Volume II.

The following information is an addition to the operation section of the Operation and Maintenance Manual. The new information is effective with SBR591-UP.

Show/hide table

No clearance for person in this area when machine turns. Severe injury or death from crushing could occur.

Note: To install the steering frame lock the machine must be in the straight ahead position.

The steering frame lock is located at the articulating hitch in the center of the machine.

Show/hide table




Illustration 1	g01438688

Install the steering frame lock when the machine is being lifted and when the machine is being transported. Also install the steering frame lock if you are performing service work near the articulating hitch. Install pin (1) through the bores of the front and rear frames, as shown.

Show/hide table




Illustration 2	g01438689

Remove the steering frame lock before the machine is operated. Remove pin (1) from the bores of the front and rear frames and install it in the stored position bore, as shown. The bore for storing the pin is located in the rear frame.

Caterpillar Information System:

2007/12/17 Correction to Operation and Maintenance Manual , "Fuel Shutoff Valve" {1329}

2007/12/17 Correction to Operation and Maintenance Manual , "Indicators" {7400, 7450}

2007/12/17 Correction to Operation and Maintenance Manual , "Additional Messages" {7000}

R2900G (JLK) Load Haul Dump Retrofitting The Battery Isolation Control{1402, 1408, 1411} R2900G (JLK) Load Haul Dump Retrofitting The Battery Isolation Control{1402, 1408, 1411}

AP600D and BG600D Asphalt Pavers Daily Inspection

R1700G Load Haul Dump Machine Electrical System Battery Isolation Control

AP600D and BG600D Asphalt Pavers Specifications

259B3 Compact Track Loader, 247B3 and 257B Series 3 Multi Terrain Loaders and 216B Series 3, 226B3, 236B3, 242B Series 3 and 252B Series 3 Skid Steer Loaders Track Tensioner

2008/02/25 A New Plug and O-ring Are Now Used on the Cylinder Head {1100}

2008/02/25 A New Plug Assembly Is Used on the Cylinder Head of Certain Machines Engines {1100}

259B3 Compact Track Loader, 247B3 and 257B Series 3 Multi Terrain Loaders and 216B Series 3, 226B3, 236B3, 242B Series 3 and 252B Series 3 Skid Steer Loaders Sprocket

AP655D and BG655D Asphalt Pavers Sound Information and Vibration Information

2007/12/31 New Oil Suction Tube {1302}

2007/12/24 Combustion Inserts in the Cylinder Head {1100}

24M Motor Grader Machine Systems Battery - Remove and Install

450E Backhoe Loader MID 039 - CID 0247 - FMI 09

AP600D and BG600D Asphalt Pavers Operator Controls - Main Control Panel

AP600D and BG600D Asphalt Pavers Operator Controls - Secondary Control Panel

The Body and Canopy Assembly has been Lengthened on Specific Off-Highway Trucks{7258} The Body and Canopy Assembly has been Lengthened on Specific Off-Highway Trucks{7258}

2007/12/31 New Power Train Software is Now Available {7620}

3524B and C175 Engines for Off-Highway Truck/Tractors Accessory Drive

450E Backhoe Loader MID 039 - CID 0367 - FMI 04

785D Off-Highway Truck Hoist, Torque Converter and Brake Tank Suction Screen - Inspect/Clean/Replace

2008/05/12 An Improved Pinion Shaft with a New Rugged Bolted Joint Provides Consistent Torque on the Circle Drive {5207}