Inlet and Exhaust Valve Springs - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 9U-7241     | 气门弹簧压缩器     | 1     |
B     | 8S-2263     | 弹簧测试仪     | 1     |
开始:
- 拆下电子单体喷油器。 请参阅拆解和组装, "电子单体喷油器 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 下列步骤用于拆卸进气门弹劾和出气门弹簧,不用拆卸缸盖。 一次只能在一个气缸上执行该步骤。 这会防止进气门和排气门落入气缸。
- 将 将 1 号活塞定位在压缩冲程的上止点。 请参阅测试和调整, "找到 1 号活塞上止点位置"。
- 在电子控制单体喷油器套筒中安装工具 (A) 。 将工具 (A) 与单体喷油器卡箍 (1) 固定到一起。
Show/hide table
图 1 | g01260774 |
Show/hide table
图 2 | g01260809 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 拧紧全高螺母直到气门弹簧卡座 (3) 松到气门 (2) 上。
- 从气门上拆掉气门弹簧卡座 (3) 。
- 小心拆掉工具 (A) 。
- 拆下气门旋转器 (4) 。
- 从气门上拆掉排气门弹簧 (6) 和进气门弹簧 (5) 。
- 从气门导杆上拆下垫圈 (7) 。
- 用工具 (B) 检查一下气门弹簧(弹力)。 关于气门弹簧的更多信息,请参考技术规格, "缸盖气门"。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 9U-7241     | 气门弹簧压缩器     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 用干净的发动机油润滑气门杆。
- 确保已将垫圈 (7) 安装到了气门导杆上。
Show/hide table
图 3 | g01260809 |
Show/hide table
图 4 | g01260774 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 将内气门弹簧 (5) 和外气门弹簧 (6) 安装到气门 (2) 上。
- 在气门 (2) 上安装气门旋转器 (4) 。
- 利用工具 (A) 压缩内气门弹簧 (5) 和外气门弹簧 (6) 。 将气门弹簧卡座 (3) 安装到气门 (2) 上。
Show/hide table
当松开气门弹簧压缩器的时候,气门弹簧卡座会从气门中弹出。 保证气门弹簧卡座正确安装在气门推杆上。 为了防止造成人员伤害,在安装气门时,应远离气门弹簧卡座前方和气门弹簧。 |
- 拆下单体喷油器卡箍 (1) 和工具 (A) 。
End By: 安装电子单体喷油器。 请参阅 拆解和组装, "电子单体喷油器 - 安装"。
Caterpillar Information System:
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Emergency Power Off - Reset
C27 and C32 Generator Set Engines Aftercooler - Remove
C15 On-Highway Engine Clean Gas Induction Cooler - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Silicon Controlled Rectifiers - Test
C15 On-Highway Engine Fuel Pressure Sensor - Remove and Install - ARD Main Fuel Pressure Sensor
C15 On-Highway Engine Fuel Pressure Sensor - Remove and Install - ARD Pilot Fuel Pressure Sensor
3500C Marine Auxiliary Engines Factory Passwords
C15 On-Highway Engine Boost Pressure Sensor - Remove and Install
C15 On-Highway Engine Inlet Air Temperature Sensor - Remove and Install
C15 On-Highway Engine Inlet Manifold Temperature Sensor - Remove and Install
3516C Locomotive Engine Closed Crankcase Ventilation (CCV) Fumes Disposal Filter - Replace
C15 On-Highway Engine Engine Control Module - Remove and Install
2006/08/07 Marine Engines are Shipped Without Oil {1348}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Log File - Retrieve
2006/08/07 A New O-ring is Now Used {1063, 1380}
C13 and C15 On-highway Engines Kickout Bypass - Test
C13 and C15 On-highway Engines Power Take-Off - Test
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Data - Capture
3612 and 3616 Engines Crankshaft Front Seal - Remove
3612 and 3616 Engines Crankshaft Front Seal - Install
TA19-M2WD and TA19-M4WD Agricultural Transmissions Daily Inspection
3612 and 3616 Engines Crankshaft Rear Seal - Remove
3612 and 3616 Engines Crankshaft Rear Seal - Install
C13 and C15 On-highway Engines Shutdown (PTO) - Test