Front Suspension (Cylinder) - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 9M-4021     | 吊环螺栓     | 2     |
B     | 138-7576     | 连杆支架     | 2     |
C     | 189-0408     | 钩环组件     | 1     |
D     | 1P-0074     | 滑锤拉拔器总成     | 1     |
E     | 8B-7559     | 适配器     | 1     |
F     | 138-7573     | 连杆支架     | 2     |
开始:
- 拆下前悬架。 请参阅拆解和组装, "前悬架(油缸)- 拆卸"。
Show/hide table
为了避免可能造成的人身伤害,在拆解前悬架油缸前卸掉充氮压力。 |
- 将前悬架油缸 (1) 放置到适当的台架上。 前悬架油缸 (1) 的重量大约为 2449 kg (5400 lb)。 将适当的容器放置在前悬架油缸 (1) 下方。
Show/hide table
图 1 | g01285266 |
Show/hide table
为了避免可能造成的人身伤害,使用适当的支撑装置来支撑悬架油缸的重量。 不要在没有使用适当的支撑时,而尝试将悬架油缸以末端竖立。 未使用适当的支撑装置可能导致工作区域中的人员受伤甚至死亡。 |
- 将工具 (A) 和适当的起吊设备固定到缸盖 (2) 上。 缸盖 (2) 的重量约为 163 kg (360 lb)。
Show/hide table
图 2 | g01285312 |
- 拆下螺栓 (3) 。 拆下缸盖 (2) 。
- 拆下 O 形密封圈 (5) 。 拆下挡圈 (4) 。
Show/hide table
图 3 | g01285333 |
- 将壳体 (6) 中的机油放到适当的容器中以便存放或弃置。
Show/hide table
图 4 | g01285350 |
- 使用工具 (B) 和工具 (C) 以拆下活塞杆 (7) 。 活塞杆 (7) 的重量约为 875 kg (1930 lb)。
Show/hide table
图 5 | g01285370 |
- 水平放置好活塞杆 (7) 。
- 拆下环 (8) 。
Show/hide table
图 6 | g01285367 |
- 将适当的起吊设备固定到活塞 (9) 上。 活塞 (9) 的重量大约为 73 kg (160 lb)。
Show/hide table
图 7 | g01285374 |
- 拆下工具 (B) 和工具 (C) 。
- 拆下螺栓 (10) 。
- 拆下活塞 (9) 时,拆下钢珠 (11) 。
Show/hide table
图 8 | g01285380 |
- 拆下螺栓 (12) 。 拆下板 (13) 。
Show/hide table
图 9 | g01285406 |
- 将端块 (14) 向内推,以拆下护圈 (15) 。
Show/hide table
图 10 | g01285416 |
- 利用工具 (D) 和 (E) 拆下端块 (14) 。
Show/hide table
图 11 | g01285418 |
- 拆下 O 形密封圈 (16) 。
Show/hide table
图 12 | g01285428 |
- 利用工具 (F) 和适当的起吊设备拆下压盖 (17) 。
Show/hide table
图 13 | g01285431 |
- 拆下环 (23) 、O 形密封圈 (22) 、环 (21) 、环 (20) 、O 形密封圈 (19) 和环 (18) 。
Show/hide table
图 14 | g01285446 |
- 拆下环 (24) 。 拆下密封件 (25) 。
Show/hide table
图 15 | g01285455 |
- 将壳体 (6) 放在一旁。 壳体 (6) 的重量大约为 1021 kg (2250 lb)。
Show/hide table
图 16 | g01285471 |
- 拆下唇型密封 (28) 。 拆下唇型密封 (27) 。 拆下环 (26) 。
Caterpillar Information System:
12M, 140M and 160M Motor Graders Hydraulic and Steering System Hydraulic Tank Mounting
2006/09/04 New Differentials Are Used {3256, 3278}
R1700G Load Haul Dump Hydraulic System Pilot Hydraulic System
R1700G Load Haul Dump Payload Control System (PCS) - If Equipped
2006/08/07 New Fuel Line is Now Used {1274}
AccuGrade® Site Reference System (SRS) and Laser Reference System (LRS) Display (Laser Reference System)
AS2302 Vers-A-Mat Screed Manual Adjuster (Screed Plate Angle) - Remove and Install
572R Series II Pipelayer Transmission Clutch Pressure - Test
C15 Petroleum Generator Set Engines Valve Mechanism
AccuGrade® GPS Safety Messages
279C, 279C2, 289C, 289C2 and 299C Compact Track Loaders, 287C, 277C, 277C2, 287C2 and 297C Multi Terrain Loaders and 246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Machine Electronic Control System Data Link
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Secondary Steering System Electric Drive Pump (Secondary Steering)
793D Off-Highway Truck/Tractor Front Suspension (Cylinder) - Assemble
Filtration Procedure for Off-Highway Truck (769-777) Rear Axle Oil {0680, 0768, 3260, 4050} Filtration Procedure for Off-Highway Truck (769-777) Rear Axle Oil {0680, 0768, 3260, 4050}
3176C Engines for Caterpillar Built Machines Digital Sensor Supply Circuit - Test
AccuGrade® GPS General Information
Field Installation for the 281-7219 Cab Window Kit {7310} Field Installation for the 281-7219 Cab Window Kit {7310}
Starting and Charging Systems Starter Solenoid (Starter One) Test Description
3176C Engines for Caterpillar Built Machines CID 0296 FMI 09 Unable to communicate with Transmission ECM
Starting and Charging Systems Start Relay (Starter Two) Test Description
Starting and Charging Systems Starter Solenoid Power Circuit (Starter Two) Test Description
3176C Engines for Caterpillar Built Machines CID 1599 FMI 05 Engine Fan Pull Solenoid open circuit
3176C Engines for Caterpillar Built Machines CID 1599 FMI 06 Engine Fan Pull Solenoid short to ground
3176C Engines for Caterpillar Built Machines CID 1600 FMI 06 Engine Fan Push Solenoid short to ground