Transmission Clutch - Calibrate
变速箱离合器接合压力标定(利用 Caterpillar 电子技师)
利用 ET 标定变速箱离合器压力。 执行该步骤以补偿变速箱部件的变化。
注: 变矩器锁定离合器标定步骤在 7 个变速箱离合器标定步骤期间执行。
下列情况下需要进行标定:
- 代理商向客户交付前。
- 更换变速箱 ECM 后
- 更换或维修任何 ECPC 阀或主安全阀后
- 更换或重装变速箱或变矩器后
- 更换变速箱控制充油泵后
- 换档质量下降
开始标定步骤前,变速箱 ECM 必须检测下列条件:
- 停车制动器接合。
- 行车制动器被释放。
- 发动机转速为低怠速(约 700 rpm)。
- 将档位选择器置于停车位置。
- 变速箱油温高于 70 °C (158 °F) 和低于 85 °C (185 °F)。
- 变速箱输出转速(TOS)为 0 rpm。
- 不存在激活的离合器电磁阀诊断代码。
- 不存在激活的变速箱或变矩器转速传感器诊断代码。
- 不存在激活的变速箱或变矩器温度传感器诊断代码。
如果在标定中未满足其中的任何条件,步骤将立即中止。
保持压力标定需要用于测量离合器中实际压力的压力表。 可能的情况下,应采用数据视图诊断工具。 开始标定步骤前,应安装 8 个压力表。 变速箱 ECPC 阀测压口位于变速箱盖上,锁定离合器(LUC)ECPC 位于变矩器箱体上。
Show/hide table
图 1 | g01283296 |
ET 标定屏幕 |
利用 Cat ET 标定变速箱离合器压力。 从 Cat ET 中的维修菜单选择 "CALIBRATION(标定)"选项。 遵循提供的说明。 利用 Cat ET 增大离合器各自压力。 利用 Cat ET 减小离合器各自压力。 可在压力表上查看压力变化。
Caterpillar Information System:
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System System Schematic
Field Installation of the 266-2411 Backhoe Auxiliary Lines Gp (Kit) for 430E Backhoes with a Standard Stick{5057} Field Installation of the 266-2411 Backhoe Auxiliary Lines Gp (Kit) for 430E Backhoes with a Standard Stick{5057}
2006/08/21 New Seal Available for Lower Window {7301, 7310}
700 Family Articulated Trucks - Changes to the Test Lines{5057} 700 Family Articulated Trucks - Changes to the Test Lines{5057}
2006/06/26 New Assembly of the Drive Plate to the Torque Converter Improves Reliability {3279}
R1700G Load Haul Dump Window Wiper and Washer Control
Steering Release Supplement for the R1600G Load Haul Dump{4284, 4300} Steering Release Supplement for the R1600G Load Haul Dump{4284, 4300}
Steering Release Supplement for the R1700G Load Haul Dump{4284, 4300} Steering Release Supplement for the R1700G Load Haul Dump{4284, 4300}
C6.6 Engines for Caterpillar Built Machines Crankcase Breather
Depth of the Spotface on the Support Assembly on Off-Highway Trucks{7051} Depth of the Spotface on the Support Assembly on Off-Highway Trucks{7051}
572R Series II Pipelayer Transmission Lubrication Oil Pressure - Test
3176C Engines for Caterpillar Built Machines Cat Data Link Circuit - Test
Filtration Procedure for Off-Highway Truck (769-793) Transmission Oil {0680, 0768, 3030, 3177} Filtration Procedure for Off-Highway Truck (769-793) Transmission Oil {0680, 0768, 3030, 3177}
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Sideshift Slide Lock Circuit - If Equipped
C4.4 Industrial Engine Compression - Test
2006/07/03 An Improved Link is Now available {5102, 6119}
2006/06/26 A New Speed-Timing Sensor is Available {1912}
C175-16 Locomotive Engine Engine Speed Sensor
AQUILATM DrillWizard General Information
3176C Engines for Caterpillar Built Machines System Overview
AQUILATM DrillWizard Installation
572R Series II Pipelayer Priority Valve - Test and Adjust
AQUILATM DrillWizard Configuration
C6.6 Engines for Caterpillar Built Machines Fuel Priming Pump