Output Transfer Gears - Adjust
Show/hide table
Illustration 1 | g01254854 |
Adjustment of Output Transfer Gear End Play
- Prior to assembly of the components use 0.038 mm (0.0015 inch) shim stock or a standard feeler gauge to check the following:
- Ensure that the bearing cups are seated in the case assembly and the cage assembly.
- Ensure that the bearing cones are seated on the transfer gear.
- Prior to assembly, lubricate the bearing cups and the bearing cones with the lubricant that is being sealed.
- Position the case assembly (1) horizontally.
- Assemble transfer gear (2), bearings and cage assembly (5) without shims (3) or O-ring seal (6) .
- Tighten 12 bolts (7) evenly.
- Rotate transfer gear (2) at least three revolutions to seat the bearings.
- Measure gap (4) between cage assembly (5) and the case assembly (1) .
- Add shims (3) to obtain a 0.10 ± 0.05 mm (0.004 ± 0.002 inch) endplay.
- Remove 12 bolts (7). Remove cages assembly (5) .
- Install the required shims (3) .
- Lubricate O-ring seal (6) lightly with the lubricant that is being sealed.
- Install O-ring seal (6) to cage assembly (5) .
- Install cage assembly (5) and 12 bolts (7) .
- Measure end play of transfer gear (2). The end play of the transfer gear must be 0.10 ± 0.05 mm (0.004 ± 0.002 inch).
- If end play is less than 0.10 ± 0.05 mm (0.004 ± 0.002 inch), add shims. If end play is greater than 0.10 ± 0.05 mm (0.004 ± 0.002 inch), remove shims.
Caterpillar Information System:
773F and 775F Off-Highway Truck Machine Lockout Control
773F and 775F Off-Highway Truck Engine Lockout Control
773F and 775F Off-Highway Truck Engine Shutdown Switch
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 0262 - FMI 04
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 0262 - FMI 03
2006/08/07 A New Shaft Assembly for Crown Control is Now Used on Screeds for Large Asphalt Pavers {5639, 6647}
773F and 775F Off-Highway Truck Battery Disconnect Switch
R1700G Load Haul Dump Power Train Output Transfer Gears
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan
Load Haul Dump Power Train Limit Switch (STIC Lockout Control)
Procedure for Kidney Looping Track Feller Buncher Hydraulic Oil {0680, 0738, 0768, 5050, 5056} Procedure for Kidney Looping Track Feller Buncher Hydraulic Oil {0680, 0738, 0768, 5050, 5056}
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2202 - FMI 12
R1700G Load Haul Dump Power Train Wheel Bearings - Adjust
773F and 775F Off-Highway Truck Stopping the Engine if an Electrical Malfunction Occurs
C4.4 Industrial Engine Electronic Control Module
770 and 772 Off-Highway Truck Steering System Worksheets
777F Off-Highway Truck Hydraulic System Service and Parking Brake (Rear)
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 2287 - FMI 05
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 2287 - FMI 06
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 2288 - FMI 05
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 2288 - FMI 06
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 2289 - FMI 05
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 2289 - FMI 06
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 2290 - FMI 05