Pump Drive - Assemble
组装步骤
Show/hide table
需要的工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
C     | 1P-0510     | 冲头组件     | 1     |
D     | 138-7573     | 连杆支架     | 3     |
E     | 1P-1861     | 挡圈钳     | 1     |
F     | -     | M-10 导向双头螺柱     | 2     |
G     | 8T-5096     | 千分表组件     | 1     |
H     | 1U-6396     | O 形密封圈装配附着剂     | 1     |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 清洁度是一项重要的因素。 进行组装步骤之前,应在清洗剂中彻底清洗所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零部件上,从而可能导致以后出现故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新件进行更换。
注: 在组装之前必须先使用丝锥清理所有需要使用密封胶的螺纹。
注: 务必更换 O 形密封圈、密封垫和密封。 旧 O 形密封圈的密封性能可能不如新 O 形密封圈。 在组装过程中使用工具 (D) 。
注: 组装之前先在所有部件上涂敷一薄层变速箱油。
- 使用工具 (E) 安装挡圈 (20) 。
Show/hide table
图 1 | g01224357 |
- 冷却轴承外圈 (21) 。 使用工具 (C) 和适当的压具,将轴承外圈 (21) 安装到惰齿轮 (16) 中。
Show/hide table
图 2 | g01224424 |
- 冷却轴承外圈 (19) 。 使用工具 (C) 和适当的压具,将轴承外圈 (19) 安装到惰齿轮 (16) 中。
Show/hide table
图 3 | g01224426 |
- 将惰齿轮 (16) 和轴承内圈 (18) 安置在变矩器壳体中。
Show/hide table
图 4 | g01224318 |
- 将隔套 (17) 在轴承内圈 (18) 上放置到位。
Show/hide table
图 5 | g01224316 |
- 将轴承内圈 (15) 在惰齿轮 (16) 上放置到位。 安装惰轮轴 (14) 。
注: 确保对齐惰轮轴中的螺栓孔与变矩器壳体中的螺栓孔。
Show/hide table
图 6 | g01224313 |
- 安装螺栓 (13) ,拧紧至扭矩为 240 ± 40 N·m (175 ± 30 lb ft)。
Show/hide table
图 7 | g01224309 |
- 安装齿轮泵 (11) 。 将管组件 (12) 安装到变矩器壳体中。
Show/hide table
图 8 | g01224305 |
- 使用工具 (D) 和适当的起吊设备,翻转变矩器壳体。 变矩器壳体的重量约为 150 kg (331 lb)。
- 冷却轴承外圈 (10) ,将轴承外圈 (10) 安装到变矩器壳体中。
Show/hide table
图 9 | g01225521 |
- 加热轴承内圈 (9) 。 将轴承内圈 (9) 安装到泵驱动齿轮 (6) 上。
Show/hide table
图 10 | g01225517 |
- 对于轴承内圈 (8) ,重复步骤 11。
Show/hide table
图 11 | g01225514 |
- 安装密封圈 (7) 。
注: 在进行下一步之前先让泵驱动齿轮冷却。
Show/hide table
图 12 | g01224286 |
注: 在密封安装过程中必须小心,以防密封断裂。
- 将泵驱动齿轮 (6) 安装到变矩器壳体中。
注: 在安装泵驱动齿轮之前先使用润滑剂稍稍润滑要密封的密封。
Show/hide table
图 13 | g01225511 |
- 冷却轴承外圈 (5) 。 将轴承外圈 (5) 安装到泵接头 (2) 上。
Show/hide table
图 14 | g01225510 |
- 将工具 (F) 安装到变矩器壳体中。 将垫片 (4) 安装到工具 (F) 的上面。
Show/hide table
图 15 | g01225509 |
- 安装 O 形密封圈 (3) (图上未显示)。 将泵接头 (2) 在变矩器壳体上放置到位。
注: 在泵接头处于正确位置后卸下工具 (F) 。
Show/hide table
图 16 | g01225507 |
- 安装螺栓 (1) ,固定护圈到位。 拧紧螺栓 (1) 至扭矩为 55 ± 10 N·m (41 ± 7 lb ft)。
- 使用工具 (G) 测量泵驱动 (22) 的轴向间隙。 轴向间隙必须为 0.100 至 0.200 mm (0.0040 至 0.0080 in)。
注: 加减垫片组件 (4) (图上未显示)中的垫片来实现正确的轴向间隙。
Show/hide table
图 17 | g01228862 |
- 重复步骤 10 至步骤 19,组装其余的泵驱动。
End By: 安装变矩器壳体。 请参阅 解体和组装, "变矩器壳体 - 安装"。
Caterpillar Information System:
TH31 Well Servicing Transmissions Transmission and Scavenge Oil Pump - Assemble
TH31 Well Servicing Transmissions Transmission and Scavenge Oil Pump - Install
TH31 Well Servicing Transmissions Transmission and Scavenge Oil Pump - Remove
TH31 Well Servicing Transmissions Transmission Planetary - Assemble
C6.6 Engines for Caterpillar Built Machines Electronic Control System Components
2006/02/20 New Supplier for Glow Plugs {1412}
TH31 Well Servicing Transmissions Transmission and Scavenge Oil Pump - Disassemble
TH31 Well Servicing Transmissions Transmission and Torque Converter - Connect
3512B Oil Well Servicing Engine (ADEM III) Electrical Power Supply
C175 Generator Set Engines Idler Gears (Front) - Remove and Install
2006/01/02 New Bevel Gear And Pinions And Associated Components Provide Increased Service Life {3254, 3256}
EMCP3 MUI Engine Monitoring and Control
C3.3 Industrial Engine Electric Starting Motor - Remove and Install
C3.3 Industrial Engine Fan - Remove and Install
C3.3 Industrial Engine Glow Plugs - Remove and Install - If Equipped
TH35 Well Servicing Transmissions Transmission Planetary - Assemble
3126B and 3126E Truck Engines Vibration Damper
The Valve Body May Crack on Certain Remanufactured Fuel Injectors{1290} The Valve Body May Crack on Certain Remanufactured Fuel Injectors{1290}
Installation of the Machine Security System (MSS) Universal Attachment Kit {7631, 7631} Installation of the Machine Security System (MSS) Universal Attachment Kit {7631, 7631}
C6.6 Engines for Caterpillar Built Machines Basic Engine
Reman Alternator Failures {1405} Reman Alternator Failures {1405}
C175-16 and C175-20 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
2006/01/02 A Different Grommet is Used to Secure the Engine Wiring Harness {1408}
TH31 Well Servicing Transmissions Transmission and Torque Converter - Separate