CX31 On-Highway Transmission Power Train Caterpillar


Modulating Valve (Transmission Clutch) - Remove and Install

Usage:

CX31 B3X

拆卸步骤

注: 清洁度是一项重要的因素。 拆卸步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。


注意

在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。

有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。

按照本地法规和条例处置所有液体。





    图 1g01228949

  1. 卸下螺栓 (1) 和防护罩 (2) 。



    图 2g01228950

  1. 断开线束组件 (4) 。

  1. 拆下螺栓 (3) 和安全阀 (5) 。



    图 3g01228952

  1. 取下 O 形密封圈 (6) 。

  1. 对其余的安全阀重复步骤2 到 4 。

安装步骤

注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 请勿使用抹布擦干零件。 棉绒可能会留在零件上,从而引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。 尘土及其他污染物可能会损坏精密部件。 组装步骤应在清洁的工作面上进行。 务必盖上部件并采取适当保护措施。

注: 检查 O 形密封圈、垫片和密封件有无磨损或损坏。 如有必要,请更换部件。


注意

在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。

有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。

按照本地法规和条例处置所有液体。





    图 4g01228952

  1. 安装 O 形密封圈 (6) 。



    图 5g01228950

  1. 定位安全阀 (5) 并安装螺栓 (3) 。 拧紧螺栓 (3) 至扭矩为 30 ± 4 N·m (22± 3 lb ft)。 连接线束组件 (4) 。

  1. 对其余的安全阀重复步骤1 到 2 。



    图 6g01228949

  1. 安置护罩 (2) 并安装螺栓 (1) 。 用 28 ± 7 N·m (21 ± 5 lb ft) 的扭矩拧紧螺栓 (1) 。

Caterpillar Information System:

3500 Locomotive Engines Turbocharger
C175 Generator Set Engines Prelubrication Oil Pump - Remove and Install
3500 Engines Fan Drive - Assemble
C1.5 and C2.2 Engines for Caterpillar Built Marine Generator Sets Gear Group (Front)
C7 Urban Transit Bus Engines Refill Capacities and Recommendations
3126B and 3126E Truck Engines Cylinder Block
3500 Engines Fan Drive - Disassemble
C175-16 and C175-20 Engines for Caterpillar Built Machines Electronic Unit Injector Sleeve - Install
3512B Oil Well Servicing Engine (ADEM III) Sensor Supply
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Drive Plate - C-9, C9, C-10, C11, and C13 Engines
3500 Engines Fan Drive - Install
C175-16 and C175-20 Engines for Caterpillar Built Machines Electronic Unit Injector Sleeve - Remove
3500B Engines Fuel Cooler - Remove and Install
2005/12/19 Welding On Fuel And Hydraulic Tanks {0353, 0679, 1273, 5056, 7000}
C6.6 Engines for Caterpillar Built Machines General Information
3512B Oil Well Servicing Engine (ADEM III) Ether Injection System
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Drive Plate - C-15 and C15 Engines
C6.6 Engines for Caterpillar Built Machines Fuel System
EMCP3 MUI Engine Monitoring and Control
2006/01/02 New Bevel Gear And Pinions And Associated Components Provide Increased Service Life {3254, 3256}
C175 Generator Set Engines Idler Gears (Front) - Remove and Install
3512B Oil Well Servicing Engine (ADEM III) Electrical Power Supply
TH31 Well Servicing Transmissions Transmission and Torque Converter - Connect
TH31 Well Servicing Transmissions Transmission and Scavenge Oil Pump - Disassemble
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.