3500 Locomotive Engines Caterpillar


Turbocharger

Usage:

3512 2WK



Illustration 1g01228864

(1) Bolt

Put 5P-3931 Anti-Seize Compound on the threads and bearing surfaces before assembly.
Torque ... 54 ± 5 N·m (40 ± 4 lb ft)

(2) Clamp

  1. Tighten the clamps.

    Torque ... 14.0 ± 1.5 N·m (10 ± 1 lb ft)

  1. Gently tap around the clamps with a soft faced hammer.

  1. Tighten the clamps again.

    Torque ... 14.0 ± 1.5 N·m (10 ± 1 lb ft)

(3) Bolt

After tightening the bolts, close the ends of the lock plates over the bolts. Do not reuse the lock plates.
Torque ... 20 ± 1.5 N·m (15 ± 1 lb ft)

(4) Seal

Caterpillar Information System:

C175 Generator Set Engines Prelubrication Oil Pump - Remove and Install
3500 Engines Fan Drive - Assemble
C1.5 and C2.2 Engines for Caterpillar Built Marine Generator Sets Gear Group (Front)
C7 Urban Transit Bus Engines Refill Capacities and Recommendations
3126B and 3126E Truck Engines Cylinder Block
3500 Engines Fan Drive - Disassemble
C175-16 and C175-20 Engines for Caterpillar Built Machines Electronic Unit Injector Sleeve - Install
3512B Oil Well Servicing Engine (ADEM III) Sensor Supply
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Drive Plate - C-9, C9, C-10, C11, and C13 Engines
3500 Engines Fan Drive - Install
C175-16 and C175-20 Engines for Caterpillar Built Machines Electronic Unit Injector Sleeve - Remove
CX31 On-Highway Transmission Power Train Relief Valve (Torque Converter Inlet) - Remove and Install
CX31 On-Highway Transmission Power Train Modulating Valve (Transmission Clutch) - Remove and Install
3500B Engines Fuel Cooler - Remove and Install
2005/12/19 Welding On Fuel And Hydraulic Tanks {0353, 0679, 1273, 5056, 7000}
C6.6 Engines for Caterpillar Built Machines General Information
3512B Oil Well Servicing Engine (ADEM III) Ether Injection System
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Drive Plate - C-15 and C15 Engines
C6.6 Engines for Caterpillar Built Machines Fuel System
EMCP3 MUI Engine Monitoring and Control
2006/01/02 New Bevel Gear And Pinions And Associated Components Provide Increased Service Life {3254, 3256}
C175 Generator Set Engines Idler Gears (Front) - Remove and Install
3512B Oil Well Servicing Engine (ADEM III) Electrical Power Supply
TH31 Well Servicing Transmissions Transmission and Torque Converter - Connect
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.