Fan Drive - Assemble
组装步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| B | 9S-3263 | 螺纹锁固胶 | - |
注: 冷却系统的部件和重量可能根据您的配置总成而有所变化。
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 在风扇轴 (6) 上安装轴承 (7) 。 拧紧轴承 (7) 上的调整螺钉 (12) 。
Show/hide table
 | |
| 图 1 | g01228737 |
Show/hide table
 | |
| 图 2 | g01228735 |
- 将适当的起吊设备连接到皮带轮 (8) 上。 皮带轮 (8) 的重量约为 32 kg (70 lb)。 将键 (11) 和皮带轮 (8) 定位在风扇轴上。 安装螺栓 (9) 。
Show/hide table
 | |
| 图 3 | g01228847 |
- 调整螺钉 (10) 上应用工具 (B) 。 拧紧调整螺钉 (10) 。
- 将适当的起吊设备连接到风扇轴 (6) 、轴承 (7) 和皮带轮 (8) 。 风扇轴 (6) 、轴承 (7) 和皮带轮 (8) 的重量约为70kg (150lb)。 将风扇轴 (6) 、轴承 (7) 和皮带轮 (8) 放置在垂直位置。
Show/hide table
 | |
| 图 4 | g01228723 |
- 将适当的起吊设备连接在风扇组件 (1) 上。 风扇组件 (1) 的重量约为 225 kg (500 lb)。 将风扇组件 (1) 安装到风扇轴 (6) 上。 安装键 (5) 。
Show/hide table
 | |
| 图 5 | g01228708 |
- 安装护圈 (4) 。 将风扇组件 (1) 升到护圈 (4) 处。
Show/hide table
 | |
| 图 6 | g01228704 |
- 安装螺栓 (2) 。 调整螺钉 (3) 上应用工具 (B) 。 拧紧调整螺钉 (3) 。
Show/hide table
 | |
| 图 7 | g01228703 |
End By: 安装风扇驱动装置。 请参阅 拆解和组装, "风扇驱动装置 - 安装"。
Caterpillar Information System:
C1.5 and C2.2 Engines for Caterpillar Built Marine Generator Sets Gear Group (Front)
C7 Urban Transit Bus Engines Refill Capacities and Recommendations
3126B and 3126E Truck Engines Cylinder Block
3500 Engines Fan Drive - Disassemble
C175-16 and C175-20 Engines for Caterpillar Built Machines Electronic Unit Injector Sleeve - Install
3512B Oil Well Servicing Engine (ADEM III) Sensor Supply
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Drive Plate - C-9, C9, C-10, C11, and C13 Engines
3500 Engines Fan Drive - Install
C175-16 and C175-20 Engines for Caterpillar Built Machines Electronic Unit Injector Sleeve - Remove
CX31 On-Highway Transmission Power Train Relief Valve (Torque Converter Inlet) - Remove and Install
3512B Oil Well Servicing Engine (ADEM III) Pulse Width Modulated Sensor
C7 Marine Engine Electric Starting Motor
C175 Generator Set Engines Prelubrication Oil Pump - Remove and Install
3500 Locomotive Engines Turbocharger
CX31 On-Highway Transmission Power Train Modulating Valve (Transmission Clutch) - Remove and Install
3500B Engines Fuel Cooler - Remove and Install
2005/12/19 Welding On Fuel And Hydraulic Tanks {0353, 0679, 1273, 5056, 7000}
C6.6 Engines for Caterpillar Built Machines General Information
3512B Oil Well Servicing Engine (ADEM III) Ether Injection System
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Drive Plate - C-15 and C15 Engines
C6.6 Engines for Caterpillar Built Machines Fuel System
EMCP3 MUI Engine Monitoring and Control
2006/01/02 New Bevel Gear And Pinions And Associated Components Provide Increased Service Life {3254, 3256}
C175 Generator Set Engines Idler Gears (Front) - Remove and Install