Gear Group (Front)
Show/hide table
Injection timing     | ||
Engine     | Maximum rated engine speed     | Injection timing (BTC) (1)     |
C1.5/3013C Genset     | 1500     | 14° ± 1°     |
1800 | 14° ± 1°     | |
3000 | 20° ± 1°     | |
C2.2/3024C Genset     | 1500     | 12° ± 1°     |
1800 | 12° ± 1°     | |
3000 | 18° ± 1°     | |
C2.2T Genset     | 1500     | 15° ± 1°     |
1800 | 15° ± 1°     |
Show/hide table
( 1 ) | Before Top Center |
Show/hide table
Illustration 1 | g00836394 |
(1) Timing mark on the camshaft gear
(2) Timing mark on the idler gear
(3) Idler gear
(4) Timing mark on the camshaft gear
Minimum backlash for all gears ... 0.08 mm (0.003 inch)
Maximum backlash for all gears ... 0.25 mm (0.010 inch)
Note: If the backlash is greater than the maximum backlash, replace the camshaft gear, the idler gear and the crankshaft gear.
When the idler gear is installed on the shaft of the oil pump, align a timing mark on idler gear (4) with the timing mark on crankshaft gear (2). Also, align the other timing mark on idler gear (4) with the timing mark on camshaft gear (3).
Caterpillar Information System:
C7 Urban Transit Bus Engines Refill Capacities and Recommendations
3126B and 3126E Truck Engines Cylinder Block
3500 Engines Fan Drive - Disassemble
C175-16 and C175-20 Engines for Caterpillar Built Machines Electronic Unit Injector Sleeve - Install
3512B Oil Well Servicing Engine (ADEM III) Sensor Supply
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Drive Plate - C-9, C9, C-10, C11, and C13 Engines
3500 Engines Fan Drive - Install
C175-16 and C175-20 Engines for Caterpillar Built Machines Electronic Unit Injector Sleeve - Remove
CX31 On-Highway Transmission Power Train Relief Valve (Torque Converter Inlet) - Remove and Install
3512B Oil Well Servicing Engine (ADEM III) Pulse Width Modulated Sensor
C7 Marine Engine Electric Starting Motor
C7 Marine Engine Electric Starting Motor
3500 Engines Fan Drive - Assemble
C175 Generator Set Engines Prelubrication Oil Pump - Remove and Install
3500 Locomotive Engines Turbocharger
CX31 On-Highway Transmission Power Train Modulating Valve (Transmission Clutch) - Remove and Install
3500B Engines Fuel Cooler - Remove and Install
2005/12/19 Welding On Fuel And Hydraulic Tanks {0353, 0679, 1273, 5056, 7000}
C6.6 Engines for Caterpillar Built Machines General Information
3512B Oil Well Servicing Engine (ADEM III) Ether Injection System
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Drive Plate - C-15 and C15 Engines
C6.6 Engines for Caterpillar Built Machines Fuel System
EMCP3 MUI Engine Monitoring and Control
2006/01/02 New Bevel Gear And Pinions And Associated Components Provide Increased Service Life {3254, 3256}