Fan Drive - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 3S-6224     | 电动液压泵总成     | 1     |
6V-3160 | 双作用油缸     | 1     | |
3H-0468 | 拉拔器板     | 4     | |
1U-9889 | 十字挡块     | 1     | |
3H-0469 | 腿     | 2     | |
5F-7343 | 轴承拉拔器总成     | 1     | |
1A-1935 | 全高螺母     | 2     | |
1P-0510 | 冲头总成     | 1     |
开始:
- 拆下风扇驱动装置。 请参阅拆解和组装, "风扇驱动装置 - 拆卸"。
注: 冷却系统的部件和重量可能根据您的配置总成而有所变化。
- 将适当的起吊设备连接在风扇组件 (1) 上。 风扇组件 (1) 的重量约为 225 kg (500 lb)。
Show/hide table
图 1 | g01228698 |
- 松开调整螺钉 (3) 。 拆下螺栓 (2) 。
Show/hide table
图 2 | g01228703 |
- 从座圈 (4) 上降低风扇组件 (1) 。
Show/hide table
图 3 | g01228704 |
- 使用工具 (A) 拆下座圈 (4) 。
Show/hide table
图 4 | g01228705 |
- 从风扇轴 (6) 上拆下键 (5) 。 拆下风扇组件 (1) 。
Show/hide table
图 5 | g01228708 |
- 将适当的起吊设备连接到风扇轴 (6) 、轴承 (7) 和皮带轮 (8) 。 风扇轴 (6) 、轴承 (7) 和皮带轮 (8) 的重量约为70kg (150)lb。 将风扇轴 (6) 、轴承 (7) 和皮带轮 (8) 定位到适当的支撑上。
Show/hide table
图 6 | g01228723 |
- 松开调整螺钉 (10) 。 将适当的起吊设备连接到皮带轮 (8) 上。 皮带轮 (8) 的重量约为 32 kg (70 lb). 拆下螺栓 (9) 并将螺栓 (9) 安装到位置 (X) 处。 拧紧螺栓以从风扇轴处拆卸皮带轮 (8) 。 拆卸皮带轮 (8) 和键 (11) 。
Show/hide table
图 7 | g01228728 |
- 从轴承 (7) 上松开调整螺钉 (12) 。 从风扇轴 (6) 上拆下轴承 (7) 。
Show/hide table
图 8 | g01228735 |
Show/hide table
图 9 | g01228737 |
注: 标记轴承 (7) 的位置以便组装。
Caterpillar Information System:
C175-16 and C175-20 Engines for Caterpillar Built Machines Electronic Unit Injector Sleeve - Install
3512B Oil Well Servicing Engine (ADEM III) Sensor Supply
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Drive Plate - C-9, C9, C-10, C11, and C13 Engines
3500 Engines Fan Drive - Install
C175-16 and C175-20 Engines for Caterpillar Built Machines Electronic Unit Injector Sleeve - Remove
CX31 On-Highway Transmission Power Train Relief Valve (Torque Converter Inlet) - Remove and Install
3512B Oil Well Servicing Engine (ADEM III) Pulse Width Modulated Sensor
C7 Marine Engine Electric Starting Motor
C7 Marine Engine Electric Starting Motor
3512B Oil Well Servicing Engine (ADEM III) Speed Control
C6.6 Generator Sets Plate Locations and Film Locations
C175 Generator Set Engines Camshaft - Install
3126B and 3126E Truck Engines Cylinder Block
C7 Urban Transit Bus Engines Refill Capacities and Recommendations
C1.5 and C2.2 Engines for Caterpillar Built Marine Generator Sets Gear Group (Front)
3500 Engines Fan Drive - Assemble
C175 Generator Set Engines Prelubrication Oil Pump - Remove and Install
3500 Locomotive Engines Turbocharger
CX31 On-Highway Transmission Power Train Modulating Valve (Transmission Clutch) - Remove and Install
3500B Engines Fuel Cooler - Remove and Install
2005/12/19 Welding On Fuel And Hydraulic Tanks {0353, 0679, 1273, 5056, 7000}
C6.6 Engines for Caterpillar Built Machines General Information
3512B Oil Well Servicing Engine (ADEM III) Ether Injection System
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Drive Plate - C-15 and C15 Engines