Supplemental Parts and Service Information for the U.S. Navy 980G Series II{7000}
- Wheel Loader:
- 980G Series II (S/N: AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442)
Introduction
Show/hide table
 | |
| Illustration 1 | g01051135 |
This Special Instruction contains supplemental information for the U.S. Navy 980G Series II 25K (25,000 lbs) Capacity Rough Terrain Container Handler (RTCH) with the machine configuration noted in the chart below. This special instruction is a supplement to the parts and service manuals for your machine.
Show/hide table
| IMPLEMENTS | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 261-6895 HANDLER ARRANGEMENT | ||||||||||||
| S/N: S/N:AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442 | ||||||||||||
| NOTE | PART NAME | TABLE REFERENCE | ||||||||||
| REFERENCE NUMBER | ILLUSTRATION NUMBER | PART NUMBER | QTY | 1 | 2 | 3 | 4 | 5 | 6 | (Product Level) | ||
| 2 | 2Q-8514 | 1 | BRAKE GP-PARKING | |||||||||
| 3 | 2Q-8528 | 1 | LINKAGE GP-(W/O LIFT ARM & BUCKET) | |||||||||
| F | 128-8485 | 1 | TIRE & RIM AR | |||||||||
| F | 171-3038 | 1 | SCHEMATIC-HYDRAULIC (980G II) | |||||||||
| 173-0558 | 1 | HARNESS AS-ENGINE | (1) | |||||||||
| 175-4212 | 1 | OIL CHANGE GP-HIGH SPEED | (1) | |||||||||
| 183-4684 | 1 | AXLE AR-OSCILLATING (REAR, LIMITED SLIP DIFF) | (1) | |||||||||
| 183-4686 | 1 | AXLE AR-FIXED (FRONT, LIMITED SLIP DIFF) | (1) | |||||||||
| 184-4740 | 1 | STEERING AR-SECONDARY | (1) | |||||||||
| 191-0154 | 1 | INSTALLATION GP-RADIO (CB) | (1) | |||||||||
| 211-1937 | 1 | LINES GP-DIAGNOSTIC (REMOTE PRESSURE TAPS) | (1) | |||||||||
| 233-6088 | 1 | ROADING AR | (1) | |||||||||
| 98 | 256-4381 | 1 | SCHEMATIC-HYDRAULIC (CONTAINER HANDLER) | |||||||||
| 258-9848 | 1 | RECEPTACLE GP-STARTING | 3 | |||||||||
| 6 | 260-4818 | 1 | LINES GP - LIFT CYLINDER | |||||||||
| 260-4819 | 1 | LINES GP-TILT CYLINDER | 6 | |||||||||
| 260-4820 | 1 | LINES GP-AUXILIARY HYDRAULIC | 7 | |||||||||
| 12 | 261-6896 | 1 | MAST AR | |||||||||
| 261-6898 | 1 | CYLINDER & MTG GP-TILT | 8 | |||||||||
| 261-6899 | 1 | SWITCH GP-AUXILIARY | 9 | |||||||||
| 15 | 261-6900 | 1 | VALVE & MTG GP-MAIN CONTROL (3-FUNCTION) | |||||||||
| 261-6901 | 1 | PUMP GP-MTG & IMPLEMENT | 10 | |||||||||
| 261-6902 | 1 | FRAME AS-LOADER | 12 | |||||||||
| 261-6903 | 1 | FRAME AS-REAR | 13 | |||||||||
| 261-6904 | 1 | LIFTING GP | 14 | |||||||||
| 261-6905 | 1 | PLATE & FILM GP | 15 | |||||||||
| 261-6907 | 1 | WIRING GP-FRONT (MAST) | 16 | |||||||||
| F | 261-6908 | 1 | HARNESS AS-CHASSIS | |||||||||
| Y- SEPARATE ILLUSTRATION F- NOT SHOWN |
||||||||||||
Show/hide table
| ( 1 ) | Refer to Parts Manual SEBP3095 |
Parts Information
2Q-8514 BRAKE GP-PARKING
Show/hide table
 | |
| Illustration 2 | g01278329 |
2Q-8528 LINKAGE GP-REMOVAL
Show/hide table
 | |
| Illustration 3 | g01278352 |
2Q-3337 CONTROL GP-IMPLEMENT
Show/hide table
| HYDRAULIC SYSTEM | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 2Q-3337 CONTROL GP-ELECTROHYDRAULIC (3-FUNCTION) | ||||||||||||
| S/N: S/N:AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442 | ||||||||||||
| NOTE | PART NAME | TABLE REFERENCE | ||||||||||
| REFERENCE NUMBER | ILLUSTRATION NUMBER | PART NUMBER | QTY | 1 | 2 | 3 | 4 | 5 | 6 | (Product Level) | ||
| 1 | 4 | 097-9169 | 1 | SPACER (7.5X12X12-MM THK) | ||||||||
| 2 | 4 | 114-4244 | 1 | PLATE | ||||||||
| 3 | 4 | 114-8167 | 1 | BRACKET AS | ||||||||
| 4 | 4 | 122-9870 | 3 | SPRING | ||||||||
| 5 | 4 | 123-8943 | 1 | COVER | ||||||||
| 6 | 4 | 124-8355 | 1 | HARNESS AS-CONTROL (ELECTROHYDRAULIC) | ||||||||
| 7 | 4 | 125-8811 | 1 | WIRE AS | ||||||||
| 8 | 4 | 150-7654 | 1 | COVER | ||||||||
| 9 | 4 | 152-7447 | 1 | SCREW-PAN HEAD | ||||||||
| 3E-0109 | 1 | PLUG (ROCKER SWITCH) | (1) | |||||||||
| M | 5C-2874 | 4 | NUT (M5X0.8-THD) | (1) | ||||||||
| 8R-3695 | 1 | GROMMET | (1) | |||||||||
| 8T-0328 | 4 | WASHER-HARD (5.5X10X1-MM THK) | (1) | |||||||||
| 9T-4735 | 1 | SPRING | (1) | |||||||||
| 9X-2026 | 6 | WASHER (6.5X17X1-MM THK) | (1) | |||||||||
| M | 9X-2042 | 8 | SCREW-TRUSS HEAD (M6X1X12-MM) | (1) | ||||||||
| 105-2976 | 5 | FLANGE | (1) | |||||||||
| 105-3372 | 1 | SPRING | (1) | |||||||||
| 106-1582 | 1 | HOUSING | (1) | |||||||||
| 106-1584 | 2 | SPACER (6.22X9.52X85-MM THK) | (1) | |||||||||
| 114-8165 | 2 | ROD | (1) | |||||||||
| 116-4502 | 1 | SWITCH AS-ROCKER (24-VOLT, SEALED, ILLUMINATED)(HYDRAULIC LOCKOUT) | (1) | |||||||||
| 133-7215 | 3 | DEFLECTOR | (1) | |||||||||
| 139-1378 | 6 | BEARING | (1) | |||||||||
| 149-3949 | 3 | LEVER-CONTROL | (1) | |||||||||
| 150-6287 | 2 | SPACER | (1) | |||||||||
| 161-8979 | 3 | SENSOR GP-POSITION (CONTROL LEVER) | (1) | |||||||||
| M | 5C-2890 | 2 | NUT (M6X1-THD) | (1) | ||||||||
| M | 6V-7357 | 2 | BOLT (M6X1X25-MM) | (1) | ||||||||
| 8T-4205 | 2 | WASHER-HARD (7.2X14.5X2-MM THK) | (1) | |||||||||
| M | 8T-4970 | 6 | BOLT (M6X1X14-MM) | (1) | ||||||||
| M- METRIC PART | ||||||||||||
Show/hide table
| ( 1 ) | Refer to Parts Manual SEBP3095 |
Show/hide table
 | |
| Illustration 4 | g01175681 |
258-9848 RECEPTACLE GP-STARTING
Show/hide table
| ELECTRICAL AND STARTING SYSTEM | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 258-9848 RECEPTACLE GP-STARTING | ||||||||||||
| S/N: S/N:AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442 | ||||||||||||
| NOTE | PART NAME | TABLE REFERENCE | ||||||||||
| REFERENCE NUMBER | ILLUSTRATION NUMBER | PART NUMBER | QTY | 1 | 2 | 3 | 4 | 5 | 6 | (Product Level) | ||
| 1 | 5 | 5R-4467 | 1 | RECEPTACLE AS | ||||||||
| 2 | 5 | 031-0249 | 4 | LOCKNUT (10-24-THD) | ||||||||
| 3 | 5 | 258-9847 | 1 | PLATE AS | ||||||||
| 4 | 5 | 259-0551 | 1 | CABLE AS | ||||||||
| 5 | 5 | 259-0552 | 1 | CABLE AS | ||||||||
| 6V-4611 | 1 | FILM-WARNING (JUMP START, READ OMM) | (1) | |||||||||
| 9F-8125 | 4 | LOCKWASHER | (1) | |||||||||
| 205-7299 | 2 | CLIP | (1) | |||||||||
| M | 7M-9910 | 4 | SCREW-MACHINE (M10X24X25.4-MM) | (1) | ||||||||
| M | 8T-4136 | 1 | BOLT (M10X1.5X25-MM) | (1) | ||||||||
| M- METRIC PART | ||||||||||||
Show/hide table
| ( 1 ) | Refer to Parts Manual SEBP3095 |
Show/hide table
 | |
| Illustration 5 | g01158539 |
260-4818 LINES GP - LIFT
Show/hide table
 | |
| Illustration 6 | g01159178 |
Show/hide table
 | |
| Illustration 7 | g01159265 |
Show/hide table
 | |
| Illustration 8 | g01159384 |
123-2369 VALVE & MTG GP-MAIN CONTROL (3-FUNCTION)
Show/hide table
| HYDRAULIC SYSTEM | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 123-2369 VALVE & MTG GP-MAIN CONTROL (3-FUNCTION) | ||||||||||||
| S/N: S/N:AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442 | ||||||||||||
| NOTE | PART NAME | TABLE REFERENCE | ||||||||||
| REFERENCE NUMBER | ILLUSTRATION NUMBER | PART NUMBER | QTY | 1 | 2 | 3 | 4 | 5 | 6 | (Product Level) | ||
| 1 | 9 | 123-0966 | 1 | BRACKET AS | ||||||||
| 2 | 9 | 123-7701 | 1 | WIRING GP-ELECTROHYDRAULIC | ||||||||
| 3 | 9 | 141-8797 | 1 | PLATE-IDENTIFICATION | ||||||||
| 4 | 9 | 142-3998 | 1 | VALVE GP-PILOT (3-FUNCTION) | ||||||||
| 2T-1397 | 2 | CLAMP | (1) | |||||||||
| 4B-4158 | 1 | SCREW-DRIVE (3/16-12X.25) | (1) | |||||||||
| 6V-0852 | 10 | CAP-DUST | (1) | |||||||||
| 6V-3965 | 10 | FITTING AS (QUICK DISCONNECT) | (1) | |||||||||
| 7X-0611 | 3 | WASHER-HARD (20X32X3-MM THK) | (1) | |||||||||
| 8C-0564 | 1 | CONNECTOR | (1) | |||||||||
| 8W-6047 | 1 | HOSE AS | (1) | |||||||||
| 9R-2152 | 1 | HOSE AS | (1) | |||||||||
| 114-2788 | 1 | VALVE GP-MAIN CONTROL (3-FUNCTION) | (1) | |||||||||
| 114-4835 | 1 | MANIFOLD | (1) | |||||||||
| 123-0931 | 1 | TUBE AS | (1) | |||||||||
| 123-0933 | 1 | TUBE AS | (1) | |||||||||
| 123-0934 | 1 | TUBE AS | (1) | |||||||||
| 123-0935 | 1 | TUBE AS | (1) | |||||||||
| 123-0936 | 1 | TUBE AS | (1) | |||||||||
| 123-0937 | 1 | TUBE AS | (1) | |||||||||
| 123-0967 | 1 | BRACKET | (1) | |||||||||
| 123-0968 | 1 | BRACKET | (1) | |||||||||
| 123-2370 | 1 | TUBE AS | (1) | |||||||||
| 123-2371 | 1 | TUBE AS | (1) | |||||||||
| 123-2372 | 1 | TUBE AS | (1) | |||||||||
| 123-7736 | 1 | BLOCK | (1) | |||||||||
| 126-6872 | 6 | TEE | (1) | |||||||||
| 128-7063 | 2 | CONNECTOR-ORIFICE (1.7-MM) | (1) | |||||||||
| 138-8063 | 1 | TUBE AS | (1) | |||||||||
| 164-7474 | 2 | VALVE GP-CHECK | (1) | |||||||||
| 184-4496 | 1 | HOSE AS | (1) | |||||||||
| 200-5978 | 2 | STRAINER | (1) | |||||||||
| 201-8855 | 1 | TUBE AS | (1) | |||||||||
| 129-3178 | 1 | LOCKNUT (M6X1-THD) | (1) | |||||||||
| 1P-3706 | 1 | SEAL-RECTANGULAR | (1) | |||||||||
| 1P-3707 | 1 | SEAL-RECTANGULAR | (1) | |||||||||
| 3J-1907 | 30 | SEAL-O-RING | (1) | |||||||||
| 6V-3241 | 2 | SEAL-RECTANGULAR | (1) | |||||||||
| 6V-8397 | 27 | SEAL-O-RING | (1) | |||||||||
| 6V-8636 | 3 | CONNECTOR (SCREEN) | (1) | |||||||||
| 6V-8724 | 6 | ELBOW | (1) | |||||||||
| 6V-8774 | 1 | TEE | (1) | |||||||||
| 6V-8980 | 3 | ELBOW | (1) | |||||||||
| 6V-9168 | 3 | NUT (11/16-16-THD) | (1) | |||||||||
| 6V-9836 | 1 | TEE-SWIVEL | (1) | |||||||||
| 7M-8485 | 1 | SEAL-O-RING | (1) | |||||||||
| M | 7X-2553 | 4 | BOLT (M16X2X40-MM) | (1) | ||||||||
| 8T-0075 | 1 | CONNECTOR | (1) | |||||||||
| M | 8T-4139 | 4 | BOLT (M12X1.75X30-MM) | (1) | ||||||||
| M | 8T-4172 | 4 | BOLT (M10X1.5X80-MM) | (1) | ||||||||
| M | 8T-4179 | 2 | BOLT (M12X1.75X20-MM) | (1) | ||||||||
| M | 8T-4194 | 4 | BOLT (M12X1.75X50-MM) | (1) | ||||||||
| 8T-4205 | 2 | WASHER-HARD (7.2X14.5X2-MM THK) | (1) | |||||||||
| 8T-4223 | 10 | WASHER-HARD (13.5X25.5X3-MM THK) | (1) | |||||||||
| 8T-4244 | 4 | WASHER-HARD (8.8X16X2-MM THK) | (1) | |||||||||
| M | 8T-4971 | 1 | BOLT (M6X1X30-MM) | (1) | ||||||||
| M | 8T-5001 | 1 | BOLT (M12X1.75X130-MM) | (1) | ||||||||
| M | 8T-5092 | 2 | BOLT (M12X1.75X150-MM) | (1) | ||||||||
| M | 8T-6868 | 4 | BOLT (M12X1.75X80-MM) | (1) | ||||||||
| 9S-4181 | 1 | PLUG | (1) | |||||||||
| 9X-8257 | 4 | WASHER (17.5X30X3.5-MM THK) | (1) | |||||||||
| M- METRIC PART | ||||||||||||
Show/hide table
| ( 1 ) | Refer to Parts Manual SEBP3095 |
Show/hide table
 | |
| Illustration 9 | g01177569 |
2Q-3335 LINES GP LIFT
Show/hide table
| HYDRAULIC SYSTEM | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 2Q-3335 LINES GP LIFT | ||||||||||||
| S/N: S/N:AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442 | ||||||||||||
| NOTE | PART NAME | TABLE REFERENCE | ||||||||||
| REFERENCE NUMBER | ILLUSTRATION NUMBER | PART NUMBER | QTY | 1 | 2 | 3 | 4 | 5 | 6 | (Product Level) | ||
| 3V-7279 | 2 | ANGLE | (1) | |||||||||
| 114-4831 | 2 | PLATE | (1) | |||||||||
| 162-9742 | 2 | HOSE AS | (1) | |||||||||
| 162-9743 | 2 | HOSE AS | (1) | |||||||||
| 171-5319 | 1 | BRACKET | (1) | |||||||||
| 171-5320 | 1 | BRACKET | (1) | |||||||||
| 226-7659 | 1 | TUBE AS | (1) | |||||||||
| 226-7661 | 1 | TUBE AS | (1) | |||||||||
| 1P-3705 | 2 | SEAL-RECTANGULAR | (1) | |||||||||
| 4J-0520 | 12 | SEAL-O-RING | (1) | |||||||||
| 5H-4019 | 4 | COVER | (1) | |||||||||
| 7S-8920 | 2 | CLIP (SLOT) | (1) | |||||||||
| 7S-8921 | 2 | CLIP (TAB) | (1) | |||||||||
| 7X-3392 | 8 | WASHER-HARD (13.5X22.5X3-MM THK) | (1) | |||||||||
| 7X-7729 | 4 | WASHER (11X25X3-MM THK) | (1) | |||||||||
| 8C-3206 | 24 | FLANGE-HALF | (1) | |||||||||
| 8T-4121 | 36 | WASHER-HARD (11X21X2.5-MM THK) | (1) | |||||||||
| M | 8T-4133 | 6 | NUT (M10X1.5-THD) | (1) | ||||||||
| M | 8T-4139 | 8 | BOLT (M12X1.75X30-MM) | (1) | ||||||||
| M | 8T-4196 | 50 | BOLT (M10X1.5X35-MM) | (1) | ||||||||
| 8T-4223 | 8 | WASHER-HARD (13.5X25.5X3-MM THK) | (1) | |||||||||
| M | 8T-5041 | 8 | BOLT (M12X1.75X120-MM) | (1) | ||||||||
| 8T-7934 | 16 | WASHER-HARD (11X21X5-MM THK) | (1) | |||||||||
| M- METRIC PART | ||||||||||||
Show/hide table
| ( 1 ) | Refer to Parts Manual SEBP3095 |
260-4819 LINES GP-TILT
Show/hide table
| HYDRAULIC SYSTEM | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 260-4819 LINES GP-TILT | ||||||||||||
| S/N: S/N:AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442 | ||||||||||||
| NOTE | PART NAME | TABLE REFERENCE | ||||||||||
| REFERENCE NUMBER | ILLUSTRATION NUMBER | PART NUMBER | QTY | 1 | 2 | 3 | 4 | 5 | 6 | (Product Level) | ||
| 1 | 10 | 7Y-3731 | 4 | FLANGE | ||||||||
| 2 | 10 | 184-1415 | 2 | HOSE AS | ||||||||
| 3 | 10 | 260-7592 | 2 | HOSE AS | ||||||||
| 6V-0852 | 2 | CAP-DUST | (1) | |||||||||
| 6V-3965 | 2 | FITTING AS (QUICK DISCONNECT) | (1) | |||||||||
| 116-2155 | 1 | MANIFOLD | (1) | |||||||||
| 197-3295 | 8 | FLANGE-HALF | (1) | |||||||||
| 203-0187 | 2 | HOSE AS | (1) | |||||||||
| 1P-3703 | 4 | SEAL-RECTANGULAR | (1) | |||||||||
| 3D-2824 | 4 | SEAL-O-RING | (1) | |||||||||
| 3J-1907 | 2 | SEAL-O-RING | (1) | |||||||||
| 4J-0522 | 4 | SEAL-O-RING | (1) | |||||||||
| 5K-9090 | 4 | SEAL-O-RING | (1) | |||||||||
| 6V-9007 | 4 | ELBOW | (1) | |||||||||
| 6V-9746 | 4 | SEAL-O-RING | (1) | |||||||||
| 7X-3392 | 16 | WASHER-HARD (13.5X22.5X3-MM THK) | (1) | |||||||||
| 8T-4121 | 16 | WASHER-HARD (11X21X2.5-MM THK) | (1) | |||||||||
| M | 8T-4183 | 16 | BOLT (M12X1.75X40-MM) | (1) | ||||||||
| M | 8T-4196 | 16 | BOLT (M10X1.5X35-MM) | (1) | ||||||||
| M | 8T-4910 | 2 | BOLT (M12X1.75X60-MM) | (1) | ||||||||
| M | 8T-5001 | 1 | BOLT (M12X1.75X130-MM) | (1) | ||||||||
| M- METRIC PART | ||||||||||||
Show/hide table
| ( 1 ) | Refer to Parts Manual SEBP3095 |
Show/hide table
 | |
| Illustration 10 | g01159635 |
260-4820 LINES GP-AUX
Show/hide table
| HYDRAULIC SYSTEM | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 260-4820 LINES GP-AUX | ||||||||||||
| S/N: S/N:AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442 | ||||||||||||
| NOTE | PART NAME | TABLE REFERENCE | ||||||||||
| REFERENCE NUMBER | ILLUSTRATION NUMBER | PART NUMBER | QTY | 1 | 2 | 3 | 4 | 5 | 6 | (Product Level) | ||
| 1 | 11 | 138-5081 | 2 | FLANGE | ||||||||
| 2 | 11 | 153-2994 | 1 | FITTING AS (QUICK DISCONNECT, FEMALE) | ||||||||
| 3 | 11 | 153-2995 | 1 | FITTING AS (QUICK DISCONNECT, MALE) | ||||||||
| 4 | 11 | 164-9797 | 2 | HOSE AS | ||||||||
| 5 | 11 | 261-2776 | 2 | PLATE | ||||||||
| 6 | 11 | 264-8115 | 2 | HOSE AS. | ||||||||
| 7 | 11 | 6V-8642 | 2 | CONNECTOR (SCREEN) | ||||||||
| 8 | 11 | 6V-8945 | 2 | REDUCER-O-RING | ||||||||
| 197-3295 | 8 | FLANGE-HALF | (1) | |||||||||
| 2M-9780 | 2 | SEAL-O-RING | (1) | |||||||||
| 4J-0522 | 6 | SEAL-O-RING | (1) | |||||||||
| 5K-9090 | 2 | SEAL-O-RING | (1) | |||||||||
| 6V-8557 | 2 | NUT-FACE SEAL (1-7/16-12-THD) | (1) | |||||||||
| 7J-9108 | 4 | SEAL-O-RING | (1) | |||||||||
| 7X-3392 | 28 | WASHER-HARD (13.5X22.5X3-MM THK) | (1) | |||||||||
| M | 8T-4183 | 8 | BOLT (M12X1.75X40-MM) | (1) | ||||||||
| M | 8T-4184 | 4 | BOLT (M12X1.75X45-MM) | (1) | ||||||||
| M | 8T-4956 | 16 | BOLT (M12X1.75X35-MM) | (1) | ||||||||
| M- METRIC PART | ||||||||||||
Show/hide table
| ( 1 ) | Refer to Parts Manual SEBP3095 |
Show/hide table
 | |
| Illustration 11 | g01159753 |
261-6896 MAST AR.
Show/hide table
 | |
| Illustration 12 | g01160090 |
261-6898 CYLINDER GP & MAST
Show/hide table
| IMPLEMENTS | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 261-6898 CYLINDER GP & MAST | ||||||||||||
| S/N: S/N:AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442 | ||||||||||||
| NOTE | PART NAME | TABLE REFERENCE | ||||||||||
| REFERENCE NUMBER | ILLUSTRATION NUMBER | PART NUMBER | QTY | 1 | 2 | 3 | 4 | 5 | 6 | (Product Level) | ||
| 1 | 13 | 3B-8488 | 2 | FITTING-GREASE | ||||||||
| 2 | 13 | 5P-7487 | 2 | BEARING-ALIGNING | ||||||||
| 3 | 13 | 7J-1309 | 2 | BEARING | ||||||||
| 4 | 13 | 053-7754 | 2 | BAR | ||||||||
| 5 | 13 | 053-7755 | 4 | EYE-RETAINING | ||||||||
| 6 | 13 | 053-7756 | 2 | PIN | ||||||||
| 7 | 13 | 065-7833 | 2 | WASHER-TILT CYL | ||||||||
| 8 | 13 | 066-5736 | 2 | CLEVIS-TILT CYL | ||||||||
| 9 | 13 | 066-5808 | 2 | AXLE GP-DRIVE | ||||||||
| 10 | 13 | 256-9306 | 2 | CYL GP (0114-0469) | ||||||||
| 11 | 13 | 267-1312 | 2 | SPACER | ||||||||
| 12 | 13 | 267-1313 | 2 | PIN AS. | ||||||||
| 13 | 13 | 064-6059 | 2 | RETAINER-PIN | ||||||||
| 14 | 13 | 067-0407 | 2 | NUT-HEX JAM | ||||||||
| 15 | 13 | 8F-1156 | 4 | BOLT (1-1/4-7X4.75-IN) | ||||||||
| 0S-1594 | 4 | BOLT (3/8-16X1-IN) | (1) | |||||||||
| 4K-0684 | 4 | WASHER-HARD (34X55X6-MM THK) | (1) | |||||||||
| 5M-2894 | 4 | WASHER-HARD (10.2X18.5X2.5-MM THK) | (1) | |||||||||
| 8S-9104 | 2 | RING-RETAINING | (1) | |||||||||
| M | 8T-4131 | 2 | NUT (M20X2.5-THD) | (1) | ||||||||
| 8T-5439 | 2 | WASHER (21.5X45X6-MM THK) | (1) | |||||||||
| M- METRIC PART | ||||||||||||
Show/hide table
| ( 1 ) | Refer to Parts Manual SEBP3095 |
Show/hide table
 | |
| Illustration 13 | g01160301 |
261-6899 SWITCH GP-AUX
Show/hide table
| ELECTRICAL SYSTEM | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 261-6899 SWITCH GP-AUX | ||||||||||||
| S/N: S/N:AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442 | ||||||||||||
| NOTE | PART NAME | TABLE REFERENCE | ||||||||||
| REFERENCE NUMBER | ILLUSTRATION NUMBER | PART NUMBER | QTY | 1 | 2 | 3 | 4 | 5 | 6 | (Product Level) | ||
| 1 | 14 | 262-0861 | 1 | SWITCH AS-ROCKER | |
|||||||
Show/hide table
 | |
| Illustration 14 | g01161936 |
261-6900 VALVE GP-MTG (3 VALVE)
Show/hide table
 | |
| Illustration 15 | g01162238 |
Show/hide table
 | |
| Illustration 16 | g01162727 |
261-6901 PUMP GP-MTG & IMPLEMENT
Show/hide table
| HYDRAULIC SYSTEM | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 261-6901 PUMP GP-MTG & IMPLEMENT | ||||||||||||
| S/N: S/N:AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442 | ||||||||||||
| NOTE | PART NAME | TABLE REFERENCE | ||||||||||
| REFERENCE NUMBER | ILLUSTRATION NUMBER | PART NUMBER | QTY | 1 | 2 | 3 | 4 | 5 | 6 | (Product Level) | ||
| 1 | 17 | 117-5980 | 1 | HOSE AS | ||||||||
| Y | 2 | 17 | 256-3682 | 1 | PUMP GP-GR-BSC B | 11 | ||||||
| 3 | 17 | 148-8324 | 1 | CONNECTOR GP | ||||||||
| 4 | 17 | 148-8414 | 1 | REDUCER AS | ||||||||
| 5 | 5F-3106 | 1 | SEAL-O-RING | (1) | ||||||||
| 6 | 7X-0448 | 2 | NUT (5/8-11-THD) | (1) | ||||||||
| 7 | 8T-4122 | 2 | WASHER-HARD (17X32X3.5-MM THK) | (1) | ||||||||
| Y- SEPARATE ILLUSTRATION | ||||||||||||
Show/hide table
| ( 1 ) | Refer to Parts Manual SEBP3095 |
Show/hide table
 | |
| Illustration 17 | g01162989 |
256-3682 PUMP GP-GR-BSC B
Show/hide table
| HYDRAULIC SYSTEM | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 256-3682 PUMP GP-GR-BSC B | ||||||||||||
| S/N: S/N:AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442 | ||||||||||||
| NOTE | PART NAME | TABLE REFERENCE | ||||||||||
| REFERENCE NUMBER | ILLUSTRATION NUMBER | PART NUMBER | QTY | 1 | 2 | 3 | 4 | 5 | 6 | (Product Level) | ||
| F | 8J-9292 | 1 | REQUIREMENTS | |||||||||
| F | 257-9160 | 1 | KIT-SEAL | |||||||||
| 1 | 18 | 257-9161 | 1 | COVER | ||||||||
| 0S-1566 | 16 | BOLT (5/8-11X1.5-IN) | (1) | |||||||||
| 2D-6648 | 1 | RING-RETAINING | (1) | |||||||||
| 5P-8247 | 16 | WASHER-HARD (17X32X3.5-MM THK) | (1) | |||||||||
| 6E-2943 | 1 | PLUG | (1) | |||||||||
| 6J-2386 | 4 | DOWEL | (1) | |||||||||
| 6V-7351 | 2 | SEAL-O-RING | (1) | |||||||||
| 154-6000 | 1 | FLANGE AS | (1) | |||||||||
| 155-3167 | 2 | SEAL-LIP TYPE | (1) | |||||||||
| 195-0862 | 1 | GEAR | (1) | |||||||||
| 195-0864 | 1 | GEAR | (1) | |||||||||
| 224-4507 | 1 | PLATE-PRESSURE (TOP) | (1) | |||||||||
| 224-4508 | 1 | PLATE-PRESSURE (BOTTOM) | (1) | |||||||||
| F- NOT SHOWN | ||||||||||||
Show/hide table
| ( 1 ) | Refer to Parts Manual SEBP3095 |
Show/hide table
 | |
| Illustration 18 | g01163302 |
261-6902 FRAME AS.-N/ENG
Show/hide table
| FRAME AND BODY | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 261-6902 FRAME AS.-N/ENG | ||||||||||||
| S/N: S/N:AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442 | ||||||||||||
| NOTE | PART NAME | TABLE REFERENCE | ||||||||||
| REFERENCE NUMBER | ILLUSTRATION NUMBER | PART NUMBER | QTY | 1 | 2 | 3 | 4 | 5 | 6 | (Product Level) | ||
| 1 | 19 | 261-6902 | 1 | FRAME AS-LOADER | ||||||||
Show/hide table
 | |
| Illustration 19 | g01165143 |
261-6903 FRAME AS.
Show/hide table
| FRAME AND BODY | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 261-6903 FRAME AS | ||||||||||||
| S/N: S/N:AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442 | ||||||||||||
| NOTE | PART NAME | TABLE REFERENCE | ||||||||||
| REFERENCE NUMBER | ILLUSTRATION NUMBER | PART NUMBER | QTY | 1 | 2 | 3 | 4 | 5 | 6 | (Product Level) | ||
| 1 | 20 | 175-4198 | 1 | FRAME AS-REAR | ||||||||
| 216-5511 | 1 | COUNTERWEIGHT GP | (1) | |||||||||
Show/hide table
| ( 1 ) | Refer to Parts Manual SEBP3095 |
Show/hide table
 | |
| Illustration 20 | g01165785 |
261-6904 LIFTING GP.
Show/hide table
| FRAME AND BODY | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 261-6904 LIFTING GP. | ||||||||||||
| S/N: S/N:AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442 | ||||||||||||
| NOTE | PART NAME | TABLE REFERENCE | ||||||||||
| REFERENCE NUMBER | ILLUSTRATION NUMBER | PART NUMBER | QTY | 1 | 2 | 3 | 4 | 5 | 6 | (Product Level) | ||
| 1 | 21 | 261-6904 | 1 | LIFTING GP. | ||||||||
| 2 | 22 | 265-8964 | 1 | PLATE-SHIPPING | ||||||||
| 20 | 261-6903 | 1 | FRAME AS. | 13 | ||||||||
Show/hide table
 | |
| Illustration 21 | g01165971 |
Show/hide table
 | |
| Illustration 22 | g01165844 |
261-6905 LUBRICANT GP
Show/hide table
| SERVICE EQUIPMENT AND SUPPLIES | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 261-6905 LUBRICANT GP | ||||||||||||
| S/N: S/N:AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442 | ||||||||||||
| NOTE | PART NAME | TABLE REFERENCE | ||||||||||
| REFERENCE NUMBER | ILLUSTRATION NUMBER | PART NUMBER | QTY | 1 | 2 | 3 | 4 | 5 | 6 | (Product Level) | ||
| 1 | 24 | 261-6704 | 1 | FILM (AUX HYD) | ||||||||
| 2 | 24 | 261-6705 | 1 | FILM (FORK) | ||||||||
| 3 | 24 | 261-6706 | 1 | FILM (FORK TILT) | ||||||||
| 4 | 24 | 265-8964 | 1 | PLATE (SHIPPING) | ||||||||
| 5 | 23 | 207-0687 | 1 | FILM | ||||||||
| 6 | 23 | 037-2472 | 2 | FILM-WARNING | ||||||||
| 7 | 23,24 | 1P-2807 | 4 | FILM-INFORMATION (LIFT POINT) | ||||||||
| 8 | 23 | 7X-7644 | 2 | FILM-INFORMATION (TIE-DOWN) | ||||||||
| 9 | 24 | 206-6305 | 27 | FILM (RED REFLECTIVE) | ||||||||
Show/hide table
 | |
| Illustration 23 | g01167189 |
Show/hide table
 | |
| Illustration 24 | g01167190 |
261-6907 WIRING GP-MAST
Show/hide table
| ELECTRICAL AND STARTING SYSTEM | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 261-6907 WIRING GP-MAST | ||||||||||||
| S/N: S/N:AWH1858,1867,1870,1889,2077,2083,2092,2100,2379,2385,2396,2401,2412,2420,2430,2442 | ||||||||||||
| NOTE | PART NAME | TABLE REFERENCE | ||||||||||
| REFERENCE NUMBER | ILLUSTRATION NUMBER | PART NUMBER | QTY | 1 | 2 | 3 | 4 | 5 | 6 | (Product Level) | ||
| 1 | 25 | 267-8924 | 1 | HARNESS AS | ||||||||
| 2 | 25 | 3S-2093 | 5 | STRAP-CABLE | ||||||||
Show/hide table
 | |
| Illustration 25 | g01177925 |
Disassembly and Assembly
Electrohydraulic Control
Removal Procedure
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
- Remove screws (1) and bottom cover (2) .
Show/hide table
 | |
| Illustration 26 | g00829520 |
- Disconnect harness assembly (3) .
Show/hide table
 | |
| Illustration 27 | g00829522 |
- Disconnect harness assembly (4) .
Show/hide table
 | |
| Illustration 28 | g00829528 |
- Remove screws (5) and cover (6) .
Show/hide table
 | |
| Illustration 29 | g01192951 |
- Remove knobs (8) and cushions (7) .
Show/hide table
 | |
| Illustration 30 | g00829584 |
Show/hide table
 | |
| Illustration 31 | g01193040 |
- Remove knob (10) .
- Remove screws (9) and cover (11) .
- Disconnect harness assemblies (12) .
Show/hide table
 | |
| Illustration 32 | g00829591 |
- Remove nuts (13) and the washers.
Show/hide table
 | |
| Illustration 33 | g00829592 |
- Slide rods (14) toward the seat in order to remove control assembly (15) .
Show/hide table
 | |
| Illustration 34 | g00829593 |
Show/hide table
 |
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. |
 |
- Remove control assembly (15). Remove spacers (16) and any additional hardware.
Show/hide table
 | |
| Illustration 35 | g00829623 |
Show/hide table
 | |
| Illustration 36 | g00829625 |
- Remove springs (17) .
Show/hide table
 | |
| Illustration 37 | g00829626 |
Show/hide table
|
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. |
|
- Remove bolts (18), the washers, the plates, and the magnetic spacers.
Show/hide table
 | |
| Illustration 38 | g00829627 |
- Remove bolts (19) and the washers from both ends of the control assembly.
Show/hide table
 | |
| Illustration 39 | g00829645 |
- Slide rods (14) away from controls (21). Remove housing (20) and controls (21) .
Show/hide table
 | |
| Illustration 40 | g00829647 |
Show/hide table
 | |
| Illustration 41 | g00829649 |
- Remove pins (22) and controls (21) from housing (20) .
Show/hide table
 | |
| Illustration 42 | g00829652 |
Show/hide table
|
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. |
|
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install controls (21) and pins (22) in housing (20) .
Show/hide table
| | |
| Illustration 43 | g00829652 |
Show/hide table
|
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. |
|
- Install housing (20) and controls (21). Install rods (14) which hold controls (21) in place.
Show/hide table
| | |
| Illustration 44 | g00829649 |
Show/hide table
| | |
| Illustration 45 | g00829647 |
- Install bolts (19) and the washers in both ends of the control assembly.
Show/hide table
| | |
| Illustration 46 | g00829645 |
- Install the magnetic spacers, the plates, the washers, and bolts (18) .
Show/hide table
| | |
| Illustration 47 | g00829627 |
- Install springs (17) .
Show/hide table
| | |
| Illustration 48 | g00829626 |
Show/hide table
|
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. |
|
- Install spacers (16) and any additional hardware. Install control assembly (15) .
Show/hide table
| | |
| Illustration 49 | g00829625 |
Show/hide table
| | |
| Illustration 50 | g00829623 |
Show/hide table
|
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. |
|
- Install rods (14) in order to hold control assembly (15) in place.
Show/hide table
| | |
| Illustration 51 | g00829593 |
- Install nuts (13) and the washers.
Show/hide table
| | |
| Illustration 52 | g00829592 |
- Connect harness assemblies (12) .
Show/hide table
| | |
| Illustration 53 | g00829591 |
- Install cover (11) and screws (9) .
Show/hide table
| | |
| Illustration 54 | g01193040 |
Show/hide table
| | |
| Illustration 55 | g00829584 |
- Install knob (10) .
- Install cushions (7) and knobs (8) .
- Install cover (6) and screws (5) .
Show/hide table
| | |
| Illustration 56 | g01192951 |
- Connect harness assembly (4) .
Show/hide table
| | |
| Illustration 57 | g00829528 |
- Connect harness assembly (3) .
Show/hide table
| | |
| Illustration 58 | g00829522 |
- Install bottom cover (2) and screws (1) .
Show/hide table
| | |
| Illustration 59 | g00829520 |
Control Group, Lines and Mast
Removal Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| 8S-7641 | Tube | 2 | |
| 8S-8048 | Saddle | 2 | |
| 8S-7615 | Pin | 2 | |
| B | 138-7573 | Link Bracket | 1 |
- Drain the implement hydraulic system. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the correct procedure.
- Attach a suitable lifting device to cover assembly (2). Remove bolts (1) and the washers. Remove cover assembly (2). The weight of cover assembly (2) is approximately 23 kg (50 lb).
Show/hide table
 | |
| Illustration 60 | g01186759 |
- Disconnect harness assemblies (3) .
Show/hide table
 | |
| Illustration 61 | g00529320 |
- Disconnect hose assemblies (4), (5), and (6). Disconnect the hose from tube assembly (7) .
Show/hide table
 | |
| Illustration 62 | g00794001 |
- Disconnect hose assemblies (8), (9), and (10) .
Show/hide table
 | |
| Illustration 63 | g00794002 |
- Remove bolts (11). Disconnect manifold (13) from the control valve. Disconnect hose assembly (12) from the control valve.
Show/hide table
 | |
| Illustration 64 | g00794003 |
- Remove bolts (14) and the washers that hold the main control valve to the front loader frame.
Show/hide table
 | |
| Illustration 65 | g00794004 |
- Install Tooling (B) and a suitable lifting device to main control valve (15). Remove main control valve (15). The weight of main control valve (15) is approximately 145 kg (320 lb).
Show/hide table
 | |
| Illustration 66 | g01103215 |
Installation Procedure
- Install Tooling (B) and a suitable lifting device to main control valve (15). Install main control valve (15). The weight of main control valve (15) is approximately 145 kg (320 lb).
Show/hide table
| | |
| Illustration 67 | g01103215 |
- Install bolts (14) and the washers.
Show/hide table
| | |
| Illustration 68 | g00794004 |
- Install manifold (13) and bolts (11). Connect hose assembly (12) .
Show/hide table
| | |
| Illustration 69 | g00794003 |
- Connect hose assemblies (8), (9), and (10) .
Show/hide table
| | |
| Illustration 70 | g00794002 |
- Connect hose assemblies (4), (5), and (6). Connect the hose assembly to tube assembly (7) .
Show/hide table
| | |
| Illustration 71 | g00794001 |
- Connect harness assemblies (3) .
Show/hide table
| | |
| Illustration 72 | g00529320 |
- Fasten a suitable lifting device to the tilt cylinders (17). Install both tilt cylinders (17) and valve (16) .
Show/hide table
 | |
| Illustration 73 | g01188517 |
- Install both tilt cylinder lines (18) and (19) .
Show/hide table
 | |
| Illustration 74 | g01189154 |
- Install hydraulic lines. (20), (21) and (22) .
Show/hide table
 | |
| Illustration 75 | g01191477 |
- Install hydraulic lines (23) for mast lift cylinders.
Show/hide table
 | |
| Illustration 76 | g01191879 |
- Install hose assembly (23) on both sides of the machine.
Show/hide table
 | |
| Illustration 77 | g01190857 |
- Install hose assembly (24) onto hydraulic tank (25) .
Show/hide table
 | |
| Illustration 78 | g01191579 |
- Install wiring gp (27) for the mast on the main control valve (15) .
Show/hide table
 | |
| Illustration 79 | g01191981 |
- Fasten a suitable lifting device to cover assembly (2). Install cover assembly (2), bolts (1), and the washers. The weight of cover assembly (2) is approximately 23 kg (50 lb).
Show/hide table
| | |
| Illustration 80 | g01186759 |
- Fill the implement hydraulic system. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the correct procedure.
- Use a suitable lifting device (28) to install mast (29) to the front of the machine.
Show/hide table
 | |
| Illustration 81 | g01192068 |
- Position mast (29) in front of the machine. Align tilt cylinder rod end (31) to mast tilt mount (30). Align frame mount (33) to mast mount (32) .
Show/hide table
 | |
| Illustration 82 | g01192116 |
- Insert pin (34) into sleeve (32) of mast.
Show/hide table
 | |
| Illustration 83 | g01192222 |
- Use a suitable lifting device to position mast (29) between the front frame forks (33). The mast pin (34) should rest on the front frame forks (33) .
Show/hide table
 | |
| Illustration 84 | g01192295 |
- Use a suitable lifting device (35) to lift the tilt cylinders (17). Align the cylinder rod end (31) close to the cylinder rod end mount hole (29) .
Show/hide table
 | |
| Illustration 85 | g01193331 |
- Start the engine and run the engine.
- Extend the tilt cylinder rod (31) in order to align the holes (29).
Show/hide table
 | |
| Illustration 86 | g01193439 |
- Stop the engine.
- Insert pin (36) into tilt cylinder rod end.
Show/hide table
 | |
| Illustration 87 | g01193606 |
- Install pin retainer (38) and pin retainer bolts (37) .
Show/hide table
 | |
| Illustration 88 | g01193621 |
- Install pin retainers (39) on the pin (36) on each side of the fork (33). Use bolts (40) to fasten bar (41) to the pin retainers (39) .
Show/hide table
 | |
| Illustration 89 | g01193989 |
- Attach hydraulic lines. (42), (43), (44) and (45) .
Show/hide table
 | |
| Illustration 90 | g01194684 |
- Install NATO plug (46) .
Show/hide table
 | |
| Illustration 91 | g01194074 |
Lubrication
Mast Lubrication Points
Wipe off all fittings before any lubricant is applied.
Show/hide table
 | |
| Illustration 92 | g01194262 |
Apply lubricant through the remote grease fitting (1).
Show/hide table
 | |
| Illustration 93 | g01194332 |
Apply lubricant through fitting (2) on each side of the mast.
Show/hide table
 | |
| Illustration 94 | g01194342 |
Apply lubricant through fitting (3) on each side of the mast of the tilt cylinder pin.
Show/hide table
 | |
| Illustration 95 | g01194382 |
Apply lubricant through fittings (4) on the mast.
Show/hide table
 | |
| Illustration 96 | g01194472 |
Apply lubricant through fitting (5) on the fork assembly.
Show/hide table
 | |
| Illustration 97 | g01194514 |
Apply lubricant through fittings (6) on the fork assembly.
Hydraulic Schematic
980G SeriesII Hydraulic Schematic
Show/hide table
 | |
| Illustration 98 | g01224836 |
(1) Tank Gp (2) Pump Gp-Gear (3) Pump Gp-Gear (4) Pump Gp-Gear (5) Pump Gp-Gear (6) Motor Gp-Piston (7) Pump Gp-Piston (8) Valve Gp-Mounting (9) Strainer (10) Core As.-Oil Cooler (11) Valve Gp-Check (12) Filter Gp (13) Pump Gp-Piston (14) Valve Gp-Pilot (15) Valve Gp.-Steering (16) Valve Gp-Pressure Reducing (17) Valve Gp-Shuttle (18) Valve Gp-Relief (19) Valve Gp-Relief (20) Valve Gp-Check (21) Valve Gp-Check (22) Valve Gp-Check (23) Screen Gp (24) Valve Gp-Neutralizer (25) Cylinder Gp (26) Valve Gp-Control (27) Valve Gp-Relief (28) Valve Gp-Relief (29) Valve Gp-Relief (30) Choke (31) Valve Gp-Relief (32) Cylinder Gp (33) Valve Gp (34) Strainer (35) Connector (36) Connector (37) Valve Gp-Pilot (38) Valve Gp-Sequence (39) Valve Gp-Solenoid (40) Valve Gp-Presssure Reducing (41) Valve Gp-Presssure Reducing (42) Valve Gp-Solenoid (43) Valve Gp-Shuttle (44) Valve Gp-Diverter (45) Valve Gp-Pressure Reducing (46) Valve Gp-Relief (47) Mast Ar. Lift | |
Test and Adjust Information
Flash File
The 980G Series II 25K Rough Terrain Container Handler (RTCH) requires 273-6646 Implement Software Gp .
Pump Flow
At high idle with an implement system pressure of 20700 kPa (3000 psi), the pump flow for the 980G Series II 25K Rough Terrain Container Handler (RTCH) is 116 cc/rev or 292 L/min (77 US gpm).
Cycle Time-Mast
Show/hide table
| FUNCTION | DIRECTION | TIME(S) (1) (in seconds) |
| Lift | Up | 17.0 |
| Down | 30.7 | |
| Tilt | Forward | 2.7 |
| Back | 1.9 | |
| Carriage Side | Left | 5.7 |
| Right | 3.2 | |
| Positioning | Together | 5.5 |
| Apart | 4.0 |
Show/hide table
| ( 1 ) | Times are recorded with no load, high idle, and warm oil. |
Mast Contact Information
U.S. Navy Cat 980G-II RTCH (25K Capacity) Mast Contact is:
Greenfield Engineering, Inc.8110 Highway 22
P.O. Box 258
Dresden, TN 38225
Phone: (731) 364-9785Fax: (731) 364-9787Email (Equipment Information): info@greenfieldengineering.comEmail (Parts Orders): parts@greenfieldengineering.com
Top Handler Contact Information
U.S. Navy Cat 980G-II RTCH (25K Capacity) Top Handler Contact is:
Adcock's Machine, Welding & FabricationAttn: Gwen Adcock
1238 Highway 158 West
Oxford, NC 27565
Phone: (919) 693-7297Fax: (919) 693-5064
Caterpillar Information System:
904B Compact Wheel Loader Shipping the Machine
637G Wheel Tractor-Scraper Engine Air Filter Service Indicator - Inspect
631G Wheel Tractor-Scraper Engine Air Filter Service Indicator - Inspect
904B Wheel Loader Power Train Parking Brake - Test and Adjust
973D Track-Type Loader Coolant Sample (Level 1) - Obtain
C7 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
C7 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
621G, 623G and 627G Wheel Tractor-Scrapers Engine Supplement Engine - Install
966H and 972H Wheel Loaders Machine Systems Hydraulic Tank - Install
966H and 972H Wheel Loaders Machine Systems Hydraulic Tank - Remove
966H and 972H Wheel Loaders Machine Systems Hydraulic Tank - Assemble
966H and 972H Wheel Loaders Machine Systems Hydraulic Tank - Disassemble
C9 Engines for Caterpillar Built Machines Water Pump - Disassemble
904B Wheel LoaderPower Train System Pressure - Release
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0139 - FMI 03
994F Wheel Loader Machine Systems Gear Pump (Brake Cooling) - Install
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0139 - FMI 05
904B Wheel LoaderPower Train Steering Frame Lock - Separate and Connect
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0139 - FMI 06
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0140 - FMI 03
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0140 - FMI 05
2005/03/28 A New Fuel Shield is Available {1252}
3408E and 3412E Engines for Caterpillar Built Machines Engine Oil Filter Base
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0140 - FMI 06