C-15 Petroleum Engine Caterpillar


Flywheel Housing

Usage:

C-15 Z2C



Illustration 1g01037614

(1) Tighten the plug to the following torque. ... 55 ± 14 N·m (40 ± 10 lb ft)




Illustration 2g01048283

(2) Tighten the flywheel cover to the following torque. ... 47 ± 7 N·m (35 ± 5 lb ft)




Illustration 3g01037590

Typical example

Note: During assembly, inspect the following components for any foreign materials: the front face of the flywheel housing, the two sides of the flywheel housing seals and the rear face of the cylinder block. These components must be free of the following substances: oil, fuel, water, gasket adhesive, assembly compounds and any other foreign material. Apply 8T-9022 Silicone Gasket in order to fill the space between the following components: the flywheel housing, the cylinder block and the engine oil pan.

To tighten the flywheel housing bolts, use the procedure that follows:

  1. In a numerical sequence, tighten bolt 1 through bolt 9.

    Torque for bolts ... 100 ± 20 N·m (74 ± 15 lb ft)

  1. In a numerical sequence, tighten bolt 10 through bolt 24.

    Torque for bolts ... 40 ± 10 N·m (30 ± 7 lb ft)

  1. In a numerical sequence, again tighten bolt 1 through bolt 9.

    Torque for bolts ... 135 ± 20 N·m (100 ± 15 lb ft)

  1. In a numerical sequence, again tighten bolt 10 through bolt 24.

    Torque for bolts ... 55 ± 10 N·m (40 ± 7 lb ft)

Caterpillar Information System:

2003/12/01 New Seal for the Ignition Transformer Tube {1561}
C1.5 and C2.2 Marine Generator Set Engines Crankshaft Rear Seal - Install
2004/07/01 Procedure for Cylinder Head Bolt Tightening {1100}
3126E Truck Engines Refill Capacities and Recommendations
C-15 Petroleum Engine Exhaust Manifold
C1.5 and C2.2 Marine Generator Set Engines Water Temperature Regulator - Remove and Install
3126E and 3126B Commercial and Truck Engines Engine Oil Level Gauge - Calibrate
C32 Marine Engine Gear Group (Front) - Time
G3500 Engines Desired Engine Speed Signal
C1.5 and C2.2 Marine Generator Set Engines Cylinder Head - Install
C1.5 and C2.2 Marine Generator Set Engines Cylinder Head - Remove
2003/11/01 Special Instruction for Testing Oil Coolers {1378}
2003/12/01 Special Instruction for Testing Oil Coolers {1378}
General Welding Procedures {0679, 7000} General Welding Procedures {0679, 7000}
SPP101 Skid Mounted Pumper Refill Capacities
Oxidation Catalyst Converter for Stationary Engines and Non-Road Mobile Engines {1091} Oxidation Catalyst Converter for Stationary Engines and Non-Road Mobile Engines {1091}
C9 Marine Auxiliary and Marine Generator Set Engines Sensors and Electrical Connectors
C12 Marine Engines Gauges and Indicators
C9 Marine Auxiliary and Marine Generator Set Engines System Configuration Parameters
2003/12/01 A New Oil Filler Tube and New Oil Filler Cap Are Now Available {1316}
2003/12/01 A New Oil Filler Tube and New Oil Filler Cap are Now Available {1316}
C32 Marine Engine Coolant Temperature Sensor
3612 and 3616 Engines Piston and Rings - Three Ring Piston
2005/10/31 Improved Pistons Are Used for Certain 3600 and C280 Engines {1214, 1216}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.