Water Pump - Assemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
C | 1P-0510 | 冲头总成 | 1 |
D | 7N-8268 | 安装工具 | 1 |
E | 438-8155 | 安装工具 | 1 |
参考: 参考再使用和修补指南, SEBF8418, "3500 系列发动机水泵的修补"以了解再使用和修补指南。
- 将滤清器 (15) 安装到泵壳体 (10) 中。
Show/hide table
图 2 g06133753 - 按照环 (14) 和定位销。
- 使用工具 (C) 将唇形密封 (13) 安装到泵壳体 (10) 中。
Show/hide table
图 3 g06133750 - 将轴组件 (8)、止推垫圈 (9)、螺栓 (7) 和垫圈安装到泵壳体 (10) 中。
Show/hide table
图 4 g06133755 Show/hide table图 5 g03476619 - 使用工具 (D) 安装固定密封件总成 (11),使陶瓷侧朝外。
Show/hide table
图 6 g06133756 Show/hide table图 7 g06133757 - 使用工具 (E) 和适当的压具安装旋转密封件总成 (6)。 使用安装夹 (X) 将旋转密封件总成 (6) 安装到位,直到旋转密封件总成 (6) 完全座入。 拆下安装夹 (X)。
注: 请勿使用锤子安装密封件总成,因为这会损坏密封件总成的陶瓷表面。
Show/hide table图 8 g06133758 - 用一薄层发动机机油润滑轴组件。 使用适当的压具将叶轮 (5) 安装在泵壳体 (10) 中以及轴组件上。 安装叶轮 (5),使轴组件端部与叶轮外表面之间的深度为
0.0 ± 0.15 mm (0.00000 ± 0.00591 inch) 。注: 支撑轴组件,以防止损坏止推垫圈。
Show/hide table图 9 g06133759 - 将螺塞组件 (12) 和 O 形密封圈安装到泵壳体 (10) 中。
Show/hide table
图 10 g03475339 - 将 O 形密封圈 (4) 和 O 形密封圈 (3) 安装在盖组件 (2) 上。
Show/hide table
图 11 g03475023 - 安装盖组件 (2)、螺柱和螺母 (1)。 拧紧螺柱至扭矩为
35 ± 5 N·m (25 ± 3 lb ft) 。 拧紧螺母 (1) 至扭矩为27 ± 5 N·m (19 ± 3 lb ft) 。
Show/hide table
图 1 | g06133754 |
结束:
- 安装水泵。
Caterpillar Information System:
G3520C and G3520E Generator Set Engines Water Pump - Disassemble
2004/03/01 Ordering a Replacement Machine Identification Plate {7405, 7557}
G3500 Engines Replacing the ECM
C32 Marine Engine Engine Description
2003/12/01 A New Dowel Improves Lubrication to the Rocker Assembly {1123, 1123}
C32 Marine Engine Model View Illustrations
C32 Marine Engine Safety Messages
G3500 Engines Customer Parameters Worksheet
2004/04/01 A New Waterproof Tachometer is Available {7450, 7462}
2003/11/01 An Improved Piston is Used {1214}
C7 Marine Engine Product Storage
C18 Marine Engines Product Lifting
G3500 Engines Troubleshooting Data Sheet
G3500 Engines MID 018 - CID 0553 - FMI 11 Oxygen Signal present when it should not have been
C9 Marine Auxiliary and Generator Set Engines Safety Messages
Federal Emissions Warranty Information General Information
G3500 Engines MID 018 - CID 0554 - FMI 11 Oxygen Signal missing during O2 calibration step
C9 Marine Auxiliary and Generator Set Engines Plate Locations and Film Locations
G3500 Engines MID 018 - CID 0555 - FMI 02 Noisy Oxygen signal
G3500 Engines MID 018 - CID 0556 - FMI 11 Oxygen Sensor Calculated Gain out of range
G3500 Engines MID 018 - CID 0557 - FMI 11 Oxygen Sensor Calculated Offset out of range
G3500 Engines MID 018 - CID 0560 - FMI 02 Cat Data Link fault
G3500 Engines MID 018 - CID 0563 - FMI 11 Loss of Desired Speed Signal
G3500 Engines MID 018 - CID 0564 - FMI 02 Noisy Desired Speed Signal