Replacing the ECM
电子控制模块(ECM)不含任何活动零件。 ECM的更换会很耗时。 在更换ECM之前,遵照本手册故障诊断和排除程序去做,以确保更换ECM之后故障将被排除。
确认可疑ECM即是故障的起因。 安装测试ECM来替换疑故障的ECM。 将软件从可疑ECM输送到测试ECM。 对测试ECM的所有参数进行编程数值,以便使其与可疑ECM的参数相符。 参数必须相符。 请参阅编程参数下列详细测试步骤。
如果测试ECM将故障排除,应重新装回疑故障的ECM。 确认故障重又出现。 如果故障重现,用测试ECM更换可疑ECM。
注: 如果这些参数无法从疑有问题的ECM读取,则必须从记录或从工厂获得这些参数。
进行下述程序来更换ECM。
注: 更换ECM之前,记录所有诊断代码。
- 记录可疑ECM的参数值。
- 如果您正在使用数字诊断工具(DDT),手动将参数复制到"用户规定参数工作表"上。
- 如果您正使用卡特彼勒电子技师(ET),使用卡特彼勒ET的"维修/复制配置/ECM更换(Service/Copy Configuration/ECM Replacement)"功能。
保存文件。 您可以选择"从ECM装载(Load from ECM)"。 也可选择"打印"功能,以获取参数设置的纸上复制文件。
- 更换ECM。
- 将发动机控制置于"断电/复位(OFF/RESET)"模式。
- 断开发动机的电源。
Show/hide table图 1 g01047096
典型的ECM控制面板
(1) 螺栓和垫圈
(2) 接头
- 断开那2个电路接点 (2) 。
- 拆下那8个螺栓和8个垫圈 (1) 。
- 拆下ECM。
注: 不要终止卡特彼勒ET。
- 使用安装紧固件,安装新ECM。
- 接通发动机电源。
- 将发动机控制置于"停机(STOP)"模式。
- 将配置参数和监测系统参数编程设置到更换的ECM内。
- 如果正使用DDT,手动将"用户规定参数工作表"中的参数编程设置到ECM中。
- 如果您正使用卡特彼勒ET,从下拉菜单中选择"文件/选择ECM(File/Select ECM)"。
- 选择更换的ECM并点击"确定(OK)"。
- 从下拉菜单中选择"维修/复制配置/ECM更换(Service/Copy Configuration/ECM Replacement)"。 点击窗口上的"确定(OK)"。
- 从屏幕左下角选择"编程ECM(Program ECM)"。 选择更换的ECM并点击"确定(OK)"。 如果显示的ECM正确,选择"是(Yes)"。
- 装载完毕后,带有"编程冲突警告(Programming Conflict Warning)"信息的窗口将会出现。 选择"确定(OK)"。
- 带有"编程ECM结果(Program ECM Results)"信息的窗口将会出现。 选择"确定(OK)"。
Caterpillar Information System:
C32 Marine Engine Engine Description
2003/12/01 A New Dowel Improves Lubrication to the Rocker Assembly {1123, 1123}
C32 Marine Engine Model View Illustrations
C32 Marine Engine Safety Messages
G3500 Engines Customer Parameters Worksheet
2004/04/01 A New Waterproof Tachometer is Available {7450, 7462}
2003/11/01 An Improved Piston is Used {1214}
C7 Marine Engine Product Storage
C18 Marine Engines Product Lifting
2003/12/01 Prevent the Possibility of Contamination in order to Ensure Longer Life of Turbochargers {1052}
2004/04/01 Prevent the Possibility of Contamination in order to Ensure Longer Life of Turbochargers {1052}
2003/12/15 Prevent the Possibility of Contamination in order to Ensure Longer Life of Turbochargers {1052}
2004/03/01 Ordering a Replacement Machine Identification Plate {7405, 7557}
G3520C and G3520E Generator Set Engines Water Pump - Disassemble
G3520C and G3520E Generator Set Engines Water Pump - Assemble
G3500 Engines Troubleshooting Data Sheet
G3500 Engines MID 018 - CID 0553 - FMI 11 Oxygen Signal present when it should not have been
C9 Marine Auxiliary and Generator Set Engines Safety Messages
Federal Emissions Warranty Information General Information
G3500 Engines MID 018 - CID 0554 - FMI 11 Oxygen Signal missing during O2 calibration step
C9 Marine Auxiliary and Generator Set Engines Plate Locations and Film Locations
G3500 Engines MID 018 - CID 0555 - FMI 02 Noisy Oxygen signal
G3500 Engines MID 018 - CID 0556 - FMI 11 Oxygen Sensor Calculated Gain out of range
G3500 Engines MID 018 - CID 0557 - FMI 11 Oxygen Sensor Calculated Offset out of range