Removal Procedure
| Required Tools | |||
| Tool | Pt. No. | Description | Qty |
| A | 4C-6486 | Stand | 4 |
| 8S-7641 | Tube | 2 | |
| 8S-7621 | Tube | 2 | |
| 8S-7625 | Collar | 1 | |
| 8S-8048 | Saddle | 4 | |
| 8S-7615 | Pin | 4 | |
| 189-0411 | Shackle As | 1 | |
| - | Pipe (51 mm (2 inch) OD) | 1 | |
| B | 1P-2381 | Spanner Wrench | 1 |
| ZZ | 6V-9508 | Face Seal Plug | 2 |
| 6V-9829 | Cap As | 2 | |
Note: Mark the locations and orientations of all hose assemblies before you begin disconnecting any components.
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
 |
Cylinders equipped with lock valves can remain pressurized for very long periods of time, even with the hoses removed. Failure to relieve pressure before removing a lock valve or disassembling a cylinder can result in personal injury or death. Ensure all pressure is relieved before removing a lock valve or disassembling a cylinder. |
 |
- Use Tooling (A) to support the work tool.
 | |
| Illustration 1 | g01013336 |
 | |
| Illustration 2 | g01013350 |
- Remove bolts (1) .
 | |
| Illustration 3 | g01017457 |
- Disconnect hose assembly (2) .
- Remove bracket (3) .
 | |
| Illustration 4 | g01013943 |
- Use Tooling (B) to remove spanner nut (4) .
- Disconnect hose assembly (6) .
 | |
| Illustration 5 | g01013944 |
- Use Tooling (B) to remove spanner nut (7) .
- Remove sideshift cylinder (5) .
Installation Procedure
| Required Tools | |||
| Tool | Pt. No. | Description | Qty |
| A | 4C-6486 | Stand | 4 |
| 8S-7641 | Tube | 2 | |
| 8S-7621 | Tube | 2 | |
| 8S-7625 | Collar | 1 | |
| 8S-8048 | Saddle | 4 | |
| 8S-7615 | Pin | 4 | |
| 189-0411 | Shackle As | 1 | |
| - | Pipe (51 mm (2 inch) OD) | 1 | |
| B | 1P-2381 | Spanner Wrench | 1 |
Note: Inspect all O-ring seals for wear or for damage. Replace the components, if necessary.
Note: All hose assemblies must be reinstalled in the original locations.
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Position sideshift cylinder (5) on the work tool. Use Tooling (B) to install spanner nut (7) .
| | |
| Illustration 6 | g01013944 |
- Install the O-ring seal and hose assembly (6) .
- Use Tooling (B) to install spanner nut (4) .
| | |
| Illustration 7 | g01013943 |
| | |
| Illustration 8 | g01017457 |
- Install bracket (3) and fasten bracket (3) to the work tool with bolts (1) .
- Install the O-ring seal and hose assembly (2) .
- Remove the work tool from Tooling (A) .