Frame (Rear) - Remove and Install
Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Pt. No. | Description | Qty |
| A | 4C-6486 | Stand | 2 |
| 8S-7640 | Stand | 2 | |
| 8-7641 | Tube | 2 | |
| 8S-7611 | Tube | 2 | |
| 8S-7615 | Pin | 4 | |
| 8S-8048 | Saddle | 4 | |
| 189-0411 | Shackle As | 1 | |
| - | Pipe (51 mm (2 inch)) | 1 | |
| B | 1P-2381 | Spanner Wrench | 1 |
Start By:
- Remove the check valve. Refer to the Disassembly and Assembly Manual, "Check Valve - Remove and Install".
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (A) to support the work tool.
Show/hide table
 | |
| Illustration 1 | g01012858 |
Show/hide table
 | |
| Illustration 2 | g01012860 |
- Remove bolts (2) and bracket (3). Move hose assemblies (1) to the side.
Show/hide table
 | |
| Illustration 3 | g01012899 |
- Remove bolts (4) and bracket assembly (5) .
Show/hide table
 | |
| Illustration 4 | g01012901 |
- Use Tooling (B) to remove spanner nut (6) .
Show/hide table
 | |
| Illustration 5 | g01012903 |
- Attach a suitable lifting device to rear frame (7). The rear frame weighs approximately 165 kg (364 lb). Remove bolts (8), clamp plates (9), guide plates (10), and spacer plates (11) at the top and at the bottom of rear frame (7). Remove rear frame (7) .
Show/hide table
 | |
| Illustration 6 | g01012904 |
Show/hide table
 | |
| Illustration 7 | g01013026 |
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Pt. No. | Description | Qty |
| A | 4C-6486 | Stand | 2 |
| 8S-7640 | Stand | 2 | |
| 8-7641 | Tube | 2 | |
| 8S-7611 | Tube | 2 | |
| 8S-7615 | Pin | 4 | |
| 8S-8048 | Saddle | 4 | |
| 189-0411 | Shackle As | 1 | |
| - | Pipe (51 mm (2 inch)) | 1 | |
| B | 1P-2381 | Spanner Wrench | 1 |
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Attach a suitable lifting device to rear frame (7). the rear frame weighs approximately 165 kg (364 lb).
Show/hide table
| | |
| Illustration 8 | g01012904 |
- Position rear frame (7) on the work tool.
- Install guide plates (10), spacer plates (11), clamp plates (9), and bolts (8) at the top and at the bottom of rear frame (7) in order to fasten the rear frame to the work tool.
Show/hide table
| | |
| Illustration 9 | g01013026 |
- Use Tooling (B) to install spanner nut (6) .
Show/hide table
| | |
| Illustration 10 | g01012903 |
- Install bracket assembly (5) and secure bracket assembly (5) with bolts (4) .
Show/hide table
| | |
| Illustration 11 | g01012901 |
- Position hose assemblies (1). Install bracket (3) and bolts (2) .
Show/hide table
| | |
| Illustration 12 | g01012899 |
- Remove the work tool from Tooling (A) .
End By: Install the check valve. Refer to the Disassembly and Assembly Manual, "Check Valve - Remove and Install".
Caterpillar Information System:
321C LCR Excavator Machine Systems Swivel - Install
321C LCR Excavator Machine Systems Swivel - Remove
2003/10/01 An Improved Alternator Belt is Used {1357}
2003/09/15 An Improved Alternator Belt is Used {1357}
M325D MH Material Handler Window Washer Reservoir - Fill
315C Excavator Machine Systems Boom Cylinder - Remove and Install
345B Excavator Hydraulic System Counterweight (Removal and Installation Hydraulic System)
2003/08/18 A New Egress Ladder is Used {7254, 7255}
315C Excavator Machine Systems Stick Cylinder - Remove and Install
321C LCR Excavator Machine Systems Pilot Valve (Joystick) - Install
321C LCR Excavator Machine Systems Pilot Valve (Joystick) - Remove
321C LCR Excavator Machine Systems Pilot Valve (Travel) - Install
Custom Product Support Literature for the Hydraulic Adjustment Procedure for the Long Reach Front on 320C L, 322C L, 325C L and 330C L Excavators{5050, 5117, 5456, 5458} Custom Product Support Literature for the Hydraulic Adjustment Procedure for the Long Reach Front on 320C L, 322C L, 325C L and 330C L Excavators{5050, 5117, 5456, 5458}
321C LCR Excavator Machine Systems Cab - Remove
321C LCR Excavator Machine Systems Cab - Install
SW45 and SW60 Wheel Saws Check Valve - Remove and Install
2003/08/01 A Previous High Temperature Locknut is Used in Engine Exhaust System Groups {7553}
321C LCR Excavator Machine Systems Undercarriage Frame - Remove
321C LCR Excavator Machine Systems Undercarriage Frame - Install
2003/11/24 Remanufactured Improved Travel Motors With Increased Service Life Are Now Available {5058}
SW45 and SW60 Wheel Saws Hydraulic Cylinder (Depth) - Remove and Install
G310B, G315B and G320B Demolition and Sorting Grapples Hydraulic Cylinder - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Crankshaft - Remove
Standalone Installation of the Machine Security System (MSS) Medium Excavator{7631} Standalone Installation of the Machine Security System (MSS) Medium Excavator{7631}