| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | FT2674 | Vacuum Cap | 1 |
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Place pilot valve (8) into position, as shown. Install bolts (11). Connect harness assembly (10).
Show/hide table
Illustration 2 g01012542 - Connect hose assemblies (9) onto pilot valve (8).
Show/hide table
Illustration 3 g01012508 - Remove Tooling (A). Install cap (2) onto the hydraulic tank.
Show/hide table
Illustration 4 g01012505 - Position guard assembly (1) and install the bolts.
Show/hide table
Illustration 5 g01012541 - Raise console assembly (7) in order to position cover (5). Install screws (6) into console assembly (7).
Show/hide table
Illustration 6 g01012540 - Position the panel and install bolts (4) into the rear of the console.
Show/hide table
Illustration 7 g01012539 - Install screws (3) and install the cover onto the front of the console.
- Fill the hydraulic oil tank with clean hydraulic oil to the correct level. Refer to Operation and Maintenance Manual, "Hydraulic System Oil Level - Check" for the correct filling procedures. Refer to Operation and Maintenance Manual, "Lubricant Viscosities" for the proper oil viscosity.
| |
| Illustration 1 | g01012543 |
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | FT2674 | Vacuum Cap | 1 |
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Place pilot valve (9) into position, as shown. Install bolts (12). Connect harness assembly (11).
Show/hide table
Illustration 9 g01012566 - Connect hose assemblies (10) onto pilot valve (9).
Show/hide table
Illustration 10 g01012508 - Remove Tooling (A). Install cap (2) onto the hydraulic tank.
Show/hide table
Illustration 11 g01012505 - Position guard assembly (1) and install the bolts.
Show/hide table
Illustration 12 g01012565 - Install knob (8).
Show/hide table
Illustration 13 g01012563 - Raise console assembly (7) in order to position cover (5). Install five screws (6) into console assembly (7).
Show/hide table
Illustration 14 g01012562 - Position the panel and install bolts (4) into the rear of the console.
Show/hide table
Illustration 15 g01012561 - Install screws (3) and install the cover onto the front of the console.
- Fill the hydraulic oil tank with clean hydraulic oil to the correct level. Refer to Operation and Maintenance Manual, "Hydraulic System Oil Level - Check" for the correct filling procedures. Refer to Operation and Maintenance Manual, "Lubricant Viscosities" for the proper oil viscosity.
| |
| Illustration 8 | g01012567 |
