3054E Industrial Engine Caterpillar


Engine Oil Filter Base - Remove and Install

Usage:

3054E 304

拆卸步骤

表 1
所需工具    
工具     零件号     零件描述     数量    
A     185-3630     带式扳手组件     1    


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。



注意

在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。

有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。

按照当地法规和指令处置所有液体。


  1. 除去发动机机油滤清器组件和发动机油底壳排放塞上的所有污垢、机油和油脂。 在发动机油底壳的排放塞下放置一个合适的容器。

  1. 运行发动机,直到发动机被加热。 关闭发动机。

  1. 将放油塞和 O 形密封圈从发动机油底壳上拆下。 将发动机机油排入容器以便保存或弃置。



    图 1g01147542

  1. 拆下机油压力传感器 (1) 。 请参阅拆解和组装手册, "发动机机油压力传感器拆卸和安装"。



    图 2g01147543

  1. 用工具 (A) 拆下发动机机油滤清器 (6) 。

  1. 拆下调整螺钉 (4) 。

  1. 从缸体上拆下发动机机油滤清器底座 (3) 。 拆下密封垫 (2) 。 废弃密封垫 (2) 。

  1. 如有必要,拆下发动机机油滤清器底座的接头 (7) 。 拆下发动机机油滤清器底座的 O 形密封圈和螺塞 (6) 。 如果配备,拆下机油取样阀。

安装步骤

表 2
所需工具    
工具     零件号     零件描述    
B     9S-3263     螺纹锁固胶    


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。





    图 3g01147543

  1. 清洁机油滤清器底座 (3) 内的机油油道。 清洁缸体和发动机机油滤清器底座 (3) 的配合面。

  1. 如果拆下机油滤清器底座 (3) 的接头,检查接头 (7) 。 向接头的螺纹上涂抹工具 (B) 。 将接头 (7) 安装到机油滤清器底座 (3) 。 以 28 N·m (20.6 lb ft) 的扭矩拧紧接头。

  1. 如果拆下机油滤清器底座 (3) 的螺塞,检查螺塞 (5) 的 O 形密封圈。 必要时更换 O 形密封圈。 将 O 形密封圈和螺塞 (5) 安装到机油滤清器底座 (3) 。 将螺塞 (5) 拧紧到 12 N·m (8.8 lb ft) 的扭矩。 如果配备,安装机油取样阀。 将机油取样阀拧紧至扭矩 12 N·m (8.8 lb ft)。

    注: 新调整螺钉 (4) 前 13 mm (0.5 in) 的螺纹上有密封胶。 要重新使用旧的调整螺钉 (4) ,清除调整螺钉上的旧密封胶,然后在调整螺钉上涂抹工具 (B) 。

    注: 切勿在密封垫 (2) 上涂抹密封胶。

  1. 将新密封垫 (2) 和发动机机油滤清器底座 (3) 定位到缸体上。 安装调整螺钉 (4) ,固定发动机机油滤清器底座 (3) 。

  1. 以 22 N·m (16.2 lb ft) 的扭矩均匀拧紧调整螺钉 (4) 。

  1. 安装机油压力传感器。 请参阅拆解和组装手册, "发动机机油压力传感器 - 拆卸和安装"。

  1. 清洁机油滤清器底座 (3) 与机油滤清器滤芯 (6) 的配合面。

  1. 用清洁的发动机机油润滑机油滤清器滤芯 (6) 上的 O 形密封圈的顶部。 将新机油滤清器滤芯 (6) 旋紧到接头 (7) 上。 用手拧紧机油滤清器滤芯 (6) 。 不要用皮带扳手拧紧机油滤清器滤芯 (6) 。

  1. 检查发动机油底壳排放塞的 O 形密封圈。 必要时更换 O 形密封圈。 将 O 形密封圈安装到发动机油底壳的排放塞上,然后将排放塞安装到发动机油底壳上。 将排放塞拧紧到正确的扭矩。 有关正确扭矩的信息,请参阅拆解和组装手册, "发动机油底壳 - 拆卸和安装"。 取出发动机油底壳和机油滤清器壳体下的容器。

  1. 向润滑系统中加注发动机油。 请参阅操作和保养手册, "加注容量",以了解发动机的润滑系统容量。

Caterpillar Information System:

C11 and C13 On-Highway Engines Belt Tensioner
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Service Brake Pedal Position (Switch 1) Circuit - Test
C1.5 and C2.2 Generator Sets Voltage Regulators
2003/02/03 Special Instruction, REHS1238, "Obtaining Factory Passwords and Software Enabled Attachments" is Available {7610}
3054E Industrial Engine Fuel Priming Pump and Fuel Filter Base - Remove and Install
3054E Industrial Engine Piston Cooling Jets - Remove and Install
320B, 320B L and 320B N Excavators Swing Drive Oil Sample - Obtain
C13 and C15 Engines for Combat and Tactical Vehicles Remote PTO Accelerator Position Sensor Circuit - Test
3054E Industrial Engine Crankshaft Front Seal - Install
3054E Industrial Engine Crankshaft Front Seal - Remove
C13, C15, and C18 Tier 4 Final Engines Housing (Front)
3054E Industrial Engine Crankshaft Pulley - Remove and Install
3054E Industrial Engine Engine Oil Cooler - Remove
3054E Industrial Engine Engine Oil Cooler - Install
C13, C15, and C18 Tier 4 Final Engines Water Pump
3054E Industrial Engine Water Pump - Remove and Install
Supplement to the Operation and Maintenance Manual{0707} Supplement to the Operation and Maintenance Manual{0707}
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Tachometer Circuit - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Two Speed Axle Switch Circuit - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Vehicle Speed and Speedometer Circuit - Test
C11, C13 and C15 On-highway Engines System Overview
C18 Generator set and C18 Marine Engines Auxiliary Water Pump - Disassemble - Type 1
C18 Generator set and C18 Marine Engines Auxiliary Water Pump - Assemble - Type 1
C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Increased Engine Oil Temperature - Inspect
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.