3054E Industrial Engine Caterpillar


Crankshaft Front Seal - Remove

Usage:

3054E 304

拆卸步骤

开始:

  1. 拆下曲轴皮带轮。 请参阅拆解和组装, "曲轴皮带轮 - 拆卸和安装"。


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。



注意

在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。

有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。

按照当地法规和指令处置所有液体。


注: 如果还要拆下壳体(前),此时不要拆下曲轴前油封。 从发动机上拆下壳体(前)后,将可以很轻易地拆下曲轴前油封。 请参阅拆解和组装手册, "壳体(前)- 拆卸"。




    图 1g01020672

  1. 使用一个带三条支腿的适当拉拔器 (1) ,并将支腿安装在曲轴前油封 (2) 的下面。 将支腿锁入到位。

  1. 在曲轴 (4) 和拉拔器 (1) 之间安装一个适当的接头 (3) 。


    注意

    确保使用主唇部拆卸曲轴前油封。 不要损坏曲轴前油封壳体的边缘。


  1. 使用拉拔器 (1) 拆下曲轴前油封 (2) 。 废弃曲轴前油封 (2) 。


注意

确保使用主唇部拆卸曲轴前油封。 不要损坏曲轴前油封壳体的边缘。


Caterpillar Information System:

C13, C15, and C18 Tier 4 Final Engines Housing (Front)
3054E Industrial Engine Crankshaft Pulley - Remove and Install
C13 Engine for Combat and Tactical Vehicles Flywheel Housing
UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Ethernet Interface
C1.5 and C2.2 Generator Sets Generator Lead Connections
C13, C15, and C18 Tier 4 Final Engines Gear Group (Front)
3054E Industrial Engine Crankshaft Rear Seal - Install
C11 and C13 Engines Piston Cooling Jet
3054E Industrial Engine Camshaft - Remove and Install
C9 Marine Engines Sensors and Electrical Connectors
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Fan Override Switch Circuit - Test
C13 Engine for Combat and Tactical Vehicles Crankshaft Seals
3054E Industrial Engine Crankshaft Front Seal - Install
C13 and C15 Engines for Combat and Tactical Vehicles Remote PTO Accelerator Position Sensor Circuit - Test
320B, 320B L and 320B N Excavators Swing Drive Oil Sample - Obtain
3054E Industrial Engine Piston Cooling Jets - Remove and Install
3054E Industrial Engine Fuel Priming Pump and Fuel Filter Base - Remove and Install
2003/02/03 Special Instruction, REHS1238, "Obtaining Factory Passwords and Software Enabled Attachments" is Available {7610}
C1.5 and C2.2 Generator Sets Voltage Regulators
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Service Brake Pedal Position (Switch 1) Circuit - Test
C11 and C13 On-Highway Engines Belt Tensioner
3054E Industrial Engine Engine Oil Filter Base - Remove and Install
3054E Industrial Engine Engine Oil Cooler - Remove
3054E Industrial Engine Engine Oil Cooler - Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.