3054E Industrial Engine Caterpillar


Crankshaft Pulley - Remove and Install

Usage:

3054E 304

拆卸步骤

开始:

  1. 拆下 V 形皮带。 请参阅拆解和组装, "V 形皮带 - 拆卸和安装"。


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。





    图 1g00952102

  1. 拆下调整螺钉 (1) 。 拆下止推垫块 (2) 。

  1. 从曲轴 (4) 上拆下皮带轮 (3) 。

安装步骤




    图 2g00952102

  1. 清洁皮带轮 (3) 和止推垫块 (2) 。 检查皮带轮 (3) 和止推垫块 (2) 有无磨损和损坏。 如有必要,更换任何损坏的部件。 检查皮带轮 (3) 上通常与曲轴前油封接触的部位 如果磨损严重,则需要安装一个耐磨衬套。 有关详细信息,请参阅拆解和组装手册, "曲轴耐磨衬套(前)- 拆卸和曲轴耐磨衬套(后)- 安装"。

  1. 将皮带轮 (3) 定位到曲轴 (4) 上。

  1. 润滑调整螺钉 (1) 的螺纹和肩。 定位止推垫块,然后安装调整螺钉 (1) 。 均匀拧紧调整螺钉至 115 N·m (85 lb ft) 的最终扭矩。

End By: 安装 V 形皮带。 请参阅 拆解和组装, "V 形皮带 - 拆卸和安装"。

Caterpillar Information System:

C13 Engine for Combat and Tactical Vehicles Flywheel Housing
UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Ethernet Interface
C1.5 and C2.2 Generator Sets Generator Lead Connections
C13, C15, and C18 Tier 4 Final Engines Gear Group (Front)
3054E Industrial Engine Crankshaft Rear Seal - Install
C11 and C13 Engines Piston Cooling Jet
3054E Industrial Engine Camshaft - Remove and Install
C9 Marine Engines Sensors and Electrical Connectors
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Fan Override Switch Circuit - Test
C13 Engine for Combat and Tactical Vehicles Crankshaft Seals
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Diagnostic Enable Switch Circuit - Test
3126B and 3126E On-highway Engines 0022-11 Primary to Secondary Engine Speed Signal Calibration (42)
C13, C15, and C18 Tier 4 Final Engines Housing (Front)
3054E Industrial Engine Crankshaft Front Seal - Remove
3054E Industrial Engine Crankshaft Front Seal - Install
C13 and C15 Engines for Combat and Tactical Vehicles Remote PTO Accelerator Position Sensor Circuit - Test
320B, 320B L and 320B N Excavators Swing Drive Oil Sample - Obtain
3054E Industrial Engine Piston Cooling Jets - Remove and Install
3054E Industrial Engine Fuel Priming Pump and Fuel Filter Base - Remove and Install
2003/02/03 Special Instruction, REHS1238, "Obtaining Factory Passwords and Software Enabled Attachments" is Available {7610}
C1.5 and C2.2 Generator Sets Voltage Regulators
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Service Brake Pedal Position (Switch 1) Circuit - Test
C11 and C13 On-Highway Engines Belt Tensioner
3054E Industrial Engine Engine Oil Filter Base - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.