Electronic Modular Control Panel II (EMCP II) For MUI Engines Caterpillar


Troubleshooting Dedicated Shutdown Indicators

Usage:

3304 02B



Illustration 1g00595806

Display Area Of Generator Set Control (GSC)

(1) Dedicated shutdown indicators

(2) Fault shutdown indicator

(3) Fault alarm indicator

(4) Upper display

(5) "DIAG" indicator

(6) Lower display

The dedicated shutdown indicators inform the operator of the system that is responsible for an engine shutdown. The symbol and the nomenclature that is nearest to the indicator identifies the responsible system. Dedicated shutdown faults are activated automatically by the GSC and the faults depend on certain setpoints. When the GSC decides that operating conditions are critical, the GSC FLASHES the corresponding shutdown indicator. Also, the GSC will shut down the engine. The GSC does not record dedicated shutdown faults in the fault log.

The dedicated shutdown indicators (faults) are listed below.

  • Low Oil Pressure

  • Emergency Stop

  • High Water Temperature

  • Engine Overspeed

  • Low Coolant Level

  • Overcrank

To find the cause of a dedicated shutdown fault, perform the correct procedure.

Caterpillar Information System:

Electronic Modular Control Panel II (EMCP II) For MUI Engines AL Fault Code - Troubleshoot
Electronic Modular Control Panel II (EMCP II) For PEEC Engines SP Fault Code - Troubleshoot
3500B Engines and 3500 Engines with EUI Option Ether Injection System
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft - Disassemble - 3003 Engines
3064 and 3066 Engines for Caterpillar Built Machines Camshaft Gear - Remove and Install
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 566 FMI 7 Unexpected Shutdown Improper Mechanical Response - Test
G3500 Engines Cylinder Head - Assemble
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 560 FMI 11 CAT Data Link Failure Mode Not Identified - Test
G3516B and G3520B Generator Set Engines Air Starting Motor - Assemble
3126B Marine Engine Electric Starting Motor
3500B Engines and 3500 Engines with EUI Option Prelubrication System
3126B Marine Engine Electric Starting Motor
G3606 and G3608 Engines Camshaft Speed Sensor - Remove and Install
3034 Engine for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines Indicator for Low Oil Pressure - Troubleshoot
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Flywheel
Electronic Modular Control Panel II (EMCP II) For PEEC Engines Indicator for Emergency Stop - Troubleshoot
G3606 and G3608 Engines Caterpillar Ignition System (CIS) Module - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines Indicator for High Water Temperature - Troubleshoot
G3606 and G3608 Engines Actuator (Hydrax) - Disassemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines Indicator for Low Coolant Level - Troubleshoot
Electronic Modular Control Panel II (EMCP II) For PEEC Engines Indicator for Overcrank - Troubleshoot
G3606 and G3608 Engines Actuator (Hydrax) - Assemble
Instructions For Correcting Speed Surge In 3406C PEEC III Truck Engines{1408} Instructions For Correcting Speed Surge In 3406C PEEC III Truck Engines{1408}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.