3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System Caterpillar


Module - Replace

Usage:

3516B 1NW
Prior to the replacement of a module, ensure that the replacement is absolutely necessary. A module is seldom the cause of a problem. Always check that the harness code is correct for the Main Display Module and that power is available to the Main Display Module. For information about a Harness Code, see Systems Operation, "Quad Gauge Module".

  1. Turn the "ECS" switch to the OFF/RESET position. Disconnect the engine harness from the Main Display Module.

  1. Make sure that the Replacement Module has the correct part number.

  1. Remove the old module and install the Replacement Module.

    Note: If the Replacement Module was previously removed from service, see Testing And Adjusting, "Main Display Module Initialization - Adjust".

  1. Connect the engine harness to the Replacement Module.

  1. Turn the "ECS" switch to the COOLDOWN/STOP position. Make sure that the Replacement Module and the Quad Gauge Electronic Modules successfully complete the Self Test. For more information on this subject, see Testing And Adjusting, "System Self Test".

  1. Set the display to English units or Metric units. See Systems Operation, "Units Mode" for more information.

Caterpillar Information System:

TK711, TK721, TK722 and TK732 Track Feller Bunchers Machine Systems Duo-Cone Conventional Seals - Install
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System Alarm Silence Switch - Troubleshoot
3606 and 3608 Engines Stub Shaft (Front)
3612 and 3616 Engines Stub Shaft (Front)
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System Clear/Mode Switch - Troubleshoot
3612 and 3616 Engines Stub Shaft (Front)
G3408 and G3412 Engines Crankshaft
3606 and 3608 Engines Vibration Damper - Single
3176C and 3196 Marine Engines Engine Oil Cooler
G3408 and G3412 Engines Engine Oil Filter Base
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System Scroll Switch - Troubleshoot
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System LH/RH Switch - Troubleshoot
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System Main Display Module Initialization - Adjust
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System Connector Contact Description of Main Display Module
3612 and 3616 Engines Stub Shaft (Front)
3606 and 3608 Engines Stub Shaft (Front)
3612 and 3616 Engines Air Inlet Shutoff
3408C and 3412C Marine Engines Magnetic Pickup
3408E and 3412E Engines for Caterpillar Built Machines Alternator Mounting
3176C Engine Reference Material
3176C Engine Engine Design
3408B and 3408C Industrial and Marine Engines Auxiliary Drive Pulley
G3300 Engines Standby Generator Set Maintenance Recommendations
3176C Engine General Information
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.