Electronic Modular Control Panel II (EMCP II) for EUI Engines Caterpillar

Service Record

Usage:

Show/hide table

Table 1
SERVICE TABLE - RECORD OF SETPOINT VALUES
Generator Description: Site, Serial No., EMCP II Model No., etc.
Setpoint	Specified Value	Actual Value ⁽¹⁾	Setpoint Description	Possible Values	Default Value
Setpoint Programming - OP5
P01			Fuel Solenoid Type	0 = ETR, 1 = ETS	0
P02			Units Shown	0 = Eng, 1 = metric	0
P03			Shutdown Override For Engine Fault	0 = shutdown, 1 = alarm	0
P04			Shutdown Override For Sensor Fault	0 = alarm, 1 = shutdown	0
P05			Coolant Loss Sensor	0 = w/o sensor, 1 = w/sensor
P06			Shutdown Override For Coolant Loss Fault	0 = shutdown, 1 = alarm	0
P07			System Voltage	0 = 24 volts, 1 = 32 volts	0
P08			Upper Display	0 = enable, 1 = disable	0
P09			Ring Gear Teeth	95 to 350 teeth	136 teeth
P10			Engine Overspeed	500 to 4330 rpm	2120 rpm
P11			Crank Terminate Speed	100 to 1000 rpm	400 rpm
P12			Oil Step Speed	400 to 1800 rpm	1350 rpm
P13			Low Oil Pressure Shutdown At Rated Speed	34 to 420 kPa (5 to 60 psi)	205 kPa (30 psi)
P14			Low Oil Pressure Shutdown At Idle Speed	20 to 336 kPa (3 to 50 psi)	70 kPa (10 psi)
P15			High Water Temperature Shutdown	94 to 123°C (201 to 253°F)	107°C (225°F)
P16			Low Water Temperature Alarm	0 to 36°C (32 to 97°F)	21°C (70°F)
P17			Total Cycle Crank Time	5 to 120 seconds	90 seconds
P18			Cycle Crank Time	5 to 60 seconds	10 seconds
P19			Cooldown Time	0 to 30 minutes	5 minutes
P20			AC Voltage Full Scale	150 V to 18000 V	700 V
P21			AC Current Full Scale	75 A to 40000 A	600 A
P22			GSC Engine Number	01 to 08	01
P23			Engine Type	0 = MUI diesel, 1 = spark ignited, 2 = EUI diesel	0
P24			Crank Time Delay	0 to 20 seconds	5 seconds
Spare Input/Output Programming - OP6
SP01			Spare Fault 1 Active State	0 = Low, 1 = High	0
SP02			Spare Fault 1 Response	0 = Shutdown, 1 = Alarm	0
SP03			Spare Fault 2 Active State	0 = Low, 1 = High	0
SP04			Spare Fault	0 = Shutdown, 1 = Alarm	0
SP05			Spare Fault	0 = Low, 1 = High	0
SP06			Spare Fault	0 = Shutdown, 1 = Alarm	0
SP07			Spare Output Active State	0 = Low, 1 = High	0
SP08			Spare Fault 1 Delay Time	0 to 250 seconds	0 seconds
SP09			Spare Fault 2 Delay Time	0 to 250 seconds	0 seconds
SP10			Spare Fault 3 Delay Time	0 to 250 seconds	0 seconds
SP11			Spare Output Response	See Service Manual	7 = cooldown
Voltmeter/Ammeter Programming - OP8
AC01			A-B Voltage Calibration	0 to 255	NA ⁽²⁾
AC02			B-C Voltage Calibration	0 to 255	⁽²⁾
AC03			C-A Voltage Calibration	0 to 255	⁽²⁾
AC04			A Current Calibration	0 to 255	⁽²⁾
AC05			B Current Calibration	0 to 255	⁽²⁾
AC06			C Current Calibration	0 to 255	⁽²⁾

Show/hide table

^( 1 )	The actual value space is provided for recording and comparing values during future servicing or troubleshooting of the particular genset.
^( 2 )	The default value is not applicable (NA). A random value is assigned to the setpoint when a GSC internal memory fault (CID 268 0 occurs.

This table provides a record of setpoint values for a singular genset. The table is intended to be an easy reference for future servicing or troubleshooting of a particular genset.