Starting Motor Magnetic Switch - Test - 3412C, 3508, 3512, and 3516 MUI Engines Only
Show/hide table
图 1 | g00442023 |
起动马达继电器的系统示意图(SMR) |
Show/hide table
图 2 | g00442025 |
早期发电机的接线盒 - 拆下了盖 位于发电机接线盒的外部。 (1) 起动马达电磁开关 |
Show/hide table
图 3 | g00737977 |
后期发电机的接线盒 - 卸下了盖 位于发电机接线盒的外部。 (1) 起动马达电磁开关 |
双起动马达系统中使用了两个起动马达电磁开关(SMMS),一台起动马达使用一个开关。
测试步骤
- 从控制面板下方将 2 号 DC 接头从控制面板上断开。 从前面板望去,2 号 DC 接头位于最左边。 使用 7X-1710 电缆探针 在控制面板下方测量接头触点 6(SMMS)和接头触点 11(B-)之间的电阻。 得到的电阻测量值应在以下范围内。
- 对于单起动马达系统:26 至 33 欧姆
- 对于双起动马达系统:26 至 33 欧姆
如果电阻不正确,更换有故障的电磁开关。 如果电阻正确,继续进行步骤 2。
- 对于单起动马达系统:26 至 33 欧姆
- 断开从小齿轮电磁阀到起动马达的电缆。 对于双起动马达系统,请在两个起动马达上执行该步骤。
- 在接线盒内的 SMMS 处,准备好连接 DC 电压表。 正极引线连接至导线 24,负极引线连接至导线 25。 (如果在双起动马达系统中测试第二个电磁开关,则将负极引线连接至导线 26。)
注: 步骤 4 4 的跨接导线通电激励起动马达电磁开关。该跨接导线仅可保持连接 10 秒钟。
- 在接线盒内的 SMMS 处,暂时在端子 1(B+)和端子 4 之间连接一根跨接导线。 测量到电压后,立即断开该导线(不要超过 10 秒钟)。 正确的测量会从 24 DCV 左右变化至 2 DCV 左右。
如果电压高于 2.0 DCV,更换电磁开关。 如果开关通过步骤 1 和步骤 4 的测试,则表明开关工作正常。 重新连接本步骤中断开的导线和电缆。
Caterpillar Information System:
3126 Truck Engine Exhaust Manifold
3126 Truck Engine Camshaft
3126B Engine for Caterpillar Built Machines Cylinder Head
C-10 and C-12 Truck Engines Basic Block
3126 Truck Engine Valve Mechanism Cover
3126 Truck Engine Cylinder Head Valves
3126 Truck Engine Valve Rocker Arms and Lifters
C-10 and C-12 Truck Engines Cooling System
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Piston and Rings
3126 Truck Engine Fuel Transfer Pump - Fuel Transfer Pump and High Pressure Oil Pump
C-10 and C-12 Truck Engines Lubrication System
3126 Truck Engine Unit Injector
C-10 and C-12 Truck Engines Electrical System
EMCPII+ for Gas Engines Symbols
3126B and 3126E Truck Engines Exhaust Elbow
C-10 and C-12 Truck Engines Compression Brake
3126B Marine Engine Rear Seal Carrier - If Equipped
3406E Truck Engines Compression Brake
C-10 and C-12 Truck Engines Basic Block
3126 Truck Engine Inlet Manifold
3126 Industrial Engine Air Inlet Elbow
3126 Truck Engine Turbocharger
3126 Industrial Engine Coolant Conditioner Base
3126 Industrial Engine Engine Oil Filter Base - Remote Filter Adapter