- Off-Highway Truck/Tractor:
- 784B (S/N: 5RK1-UP)
- Wheel Loader:
- 994 (S/N: 9YF1-UP)
- 784C (S/N: 2PZ1-UP)
- 785B (S/N: 6HK1-UP)
- 785C (S/N: 1HW1-UP; 5AZ1-UP; APX1-UP)
- 789B (S/N: 7EK1-UP)
- 789C (S/N: 2BW1-UP)
- 793B (S/N: 1HL1-UP)
- 793C (S/N: 4AR1-UP; 4GZ1-UP; ATY1-UP)
- 994D (S/N: 3TZ1-UP)
Reference: Service Magazine, SEPD0503, 01 March 2000, "New Fan Drive Group Includes Serviceable Magnet And Pinned Bearing Races"
Reference: Disassembly and Assembly Module, RENR2634, "784C Tractor and 785C, 785C HAA, 789C and 793C Off-Highway Truck Variable Speed Fan Drive", "Fan Drive - Disassemble"
Reference: Disassembly and Assembly Module, RENR2634, "784C Tractor and 785C, 785C HAA, 789C and 793C Off-Highway Truck Variable Speed Fan Drive", "Fan Drive - Assemble"
Fabricated Tools are required for the disassembly and assembly of the variable speed fan drives that are described in the References. Table 1 identifies the Fabricated Tools and the corresponding Illustrations. The illustrations provide the dimensions for making the Fabricated Tools.
The Fabricated Tools that are identified in Table 1 can be used to service the variable speed fan drives that follow: the former 100-8105 Fan Drive Gp, the former 129-9494 Fan Drive Gp, the former 133-5969 Fan Drive Gp and 163-2592 Fan Drive Gp. The Fabricated Tools that are identified in the References are the Fabricated Tools that are identified in Table 1.
The Fabricated Tools that are identified in the Service Magazine, 30 March 1998, "Use FT2461 Pressing Bar, FT2462 Pressing Tube, FT2463 Ring, FT2464 Plate, FT2465 Plate, FT2466 Mounting Plate, And FT2467 Rotating Plate To Disassmeble and Assemble Variable Speed Fan Clutch" and the Service Manual, SENR8603, "Variable Speed Fan Clutch" can NOT be used to service the 163-2592 Fan Drive Gp .
If a former variable speed fan drive must be rebuilt or repaired, the former variable speed fan drive should be replaced by a 163-2592 Fan Drive Gp .
Note: All of the Fabricated Tools that are identified in Table 1 are made of SAE 4140 steel.
Note: After the new tool is fabricated, mark the number (FTXXXX) of the Fabricated Tool on the tool.
Fabricated Tool     | Description     | Illustration     |
---|---|---|
FT2749     | Bearing Installer     | 1     |
FT2750     | Bearing Installer     | 2     |
FT2751     | Bearing Remover     | 3     |
FT2752     | Seal Installer Assembly     | 4, 5, 6     |
FT2753     | Bearing Installer     | 7     |
FT2754     | Bearing Installer     | 8     |
FT2756     | Sensor Installer     | 9     |
FT2757     | Sensor Installer     | 10     |
FT2749 Bearing Installer
Illustration 1 | g00864798 |
This illustration shows the dimensions for an FT2749 Bearing Installer. (A) This length is 114.3 ± 0.5 mm (4.50 ± 0.02 inch). (B) This length is 50.8 ± 1.0 mm (2.00 ± 0.04 inch). (C) This length is 5.08 ± 0.06 mm (0.200 ± 0.002 inch). (D) This diameter is 44.5 mm (1.75 inch). (E) This length is 50.8 ± 0.5 mm (2.00 ± 0.02 inch). (F) This diameter is 69.723 ± 0.025 mm (2.7450 ± 0.0010 inch). (G) This diameter is 82.6 ± 0.5 mm (3.25 ± 0.02 inch). (H) This diameter is 74.498 ± 0.025 mm (2.9330 ± 0.0010 inch). (I) This chamfer is 1.5 ± 0.5 mm (0.06 ± 0.02 inch) by 45 degrees. (J) This maximum radius is 0.13 mm (0.005 inch). (K) This chamfer is 1.0 ± 0.5 mm (0.04 ± 0.02 inch) by 45 degrees. (L) This is a medium knurl. |
FT2750 Bearing Installer
Illustration 2 | g00864990 |
This illustration shows the dimensions for an FT2750 Bearing Installer. (A) This length is 88.9 ± 0.5 mm (3.50 ± 0.02 inch). (B) This length is 50.8 ± 1.0 mm (2.00 ± 0.04 inch). (C) This length is 7.21 ± 0.06 mm (0.284 ± 0.002 inch). (D) This diameter is 44.5 mm (1.75 inch). (E) This length is 25.4 ± 0.5 mm (1.00 ± 0.02 inch). (F) This diameter is 69.723 ± 0.025 mm (2.7450 ± 0.0010 inch). (G) This diameter is 74.498 ± 0.025 mm (2.9330 ± 0.0010 inch). (H) This diameter is 92.1 ± 0.5 mm (3.63 ± 0.02 inch). (I) This chamfer is 1.5 ± 0.5 mm (0.06 ± 0.02 inch) by 45 degrees. (J) The maximum radius is 0.13 mm (0.005 inch). (K) This chamfer is 1.0 ± 0.5 mm (0.04 ± 0.02 inch) by 45 degrees. (L) This is a medium knurl. |
FT2751 Bearing Remover
Illustration 3 | g00865044 |
This illustration shows the dimensions for an FT2751 Bearing Remover. (A) This length is 177.8 ± 0.5 mm (7.00 ± 0.02 inch). (B) This length is 44.5 ± 1.0 mm (1.75 ± 0.04 inch). (C) This length is 127.0 ± 0.5 mm (5.00 ± 0.02 inch). (D) This diameter is 44.5 mm (1.75 inch). (E) This length is 25.40 ± 0.25 mm (1.000 ± 0.010 inch). (F) This diameter is 69.723 ± 0.025 mm (2.7450 ± 0.0010 inch). (G) This diameter is 82.6 ± 0.5 mm (3.25 ± 0.02 inch). (H) This diameter is 74.498 ± 0.025 mm (2.9330 ± 0.0010 inch). (I) This chamfer is 1.5 ± 0.5 mm (0.06 ± 0.02 inch) by 45 degrees. (J) The maximum radius is 0.13 mm (0.005 inch). (K) This chamfer is 1.0 ± 0.5 mm (0.04 ± 0.02 inch) by 45 degrees. (L) This is a medium knurl. |
FT2752 Seal Installer Assembly
The FT2752 Seal Installer Assembly is made from 2 fabricated parts. A body and a plate must be fabricated. Illustration 4 provides the dimensions for the body. Illustration 5 provides the dimensions for the plate. Put the plate into position on the body as Illustration 6 shows. Weld the plate onto the body.
Illustration 4 | g00865157 |
This illustration shows the dimensions for the body (V) of an FT2752 Seal Installer Assembly. (A) This diameter is 95.38 ± 0.13 mm (3.755 ± 0.005 inch). (B) This diameter is 95.25 ± 0.50 mm (3.750 ± 0.020 inch). (C) This diameter is 128.14 ± 1.40 mm (5.045 ± 0.055 inch). (D) This diameter is 108.0 ± 1.0 mm (4.25 ± 0.04 inch). (E) This diameter is 105.28 ± 0.13 mm (4.145 ± 0.005 inch). (F) This diameter is 70.23 ± 0.13 mm (2.765 ± 0.005 inch). (G) This chamfer is 2.5 ± 0.5 mm (0.10 ± 0.02 inch) by 45 degrees. (H) The maximum radius is 0.13 mm (0.005 inch). (I) This chamfer is 3.0 ± 0.5 mm (0.12 ± 0.02 inch) by 45 degrees. (J) This angle should be between 44 degrees and 46 degrees. (K) This radius is 1.5 ± 0.5 mm (0.06 ± 0.02 inch). (L) This length is 14.122 ± 0.025 mm (0.5560 ± 0.0010 inch). (M) This length is 60.325 ± 0.025 mm (2.3750 ± 0.0010 inch). (N) This length is 95.25 ± 0.50 mm (3.750 ± 0.020 inch). (O) This length is 111.76 ± 0.25 mm (4.400 ± 0.010 inch). (P) This length is 228.6 ± 0.5 mm (9.00 ± 0.02 inch). |
Illustration 5 | g00865296 |
This illustration shows the dimensions for the plate (W) of an FT2752 Seal Installer Assembly. (Q) This diameter is 94.0 ± 0.5 mm (3.70 ± 0.02 inch). (R) This diameter is 108.0 ± 1.0 mm (4.25 ± 0.04 inch). (S) This radius is 0.13 mm (0.005 inch). (T) This length is 6.35 ± 0.50 mm (0.250 ± 0.020 inch). (U) This length is 9.53 ± 0.05 mm (0.375 ± 0.002 inch). |
Illustration 6 | g00865331 |
This illustration shows the components of the FT2752 Seal Installer Assembly. (V) Fabricated body (W) Fabricated plate (X) Weld the fabricated body (V) to the fabricated plate (W) at three equally spaced places. The length of each weld should be 15 mm (0.6 inch). |
FT2753 Bearing Installer
Illustration 7 | g00865386 |
This illustration shows the dimensions for an FT2753 Bearing Installer. (A) This diameter is 144.0 ± 0.5 mm (5.67 ± 0.02 inch). (B) This chamfer is 1.5 ± 0.5 mm (0.06 ± 0.02 inch) by 45 degrees in two places. (C) This length is 12.7 mm (0.50 inch). |
FT2754 Bearing Installer
Illustration 8 | g00867830 |
This illustration shows the dimensions for an FT2754 Bearing Installer. (A) This diameter is 168.9 ± 0.5 mm (6.65 ± 0.02 inch). (B) This chamfer is 1.5 ± 0.5 mm (0.06 ± 0.02 inch) by 45 degrees in two places. (C) This length is 12.7 mm (0.50 inch). |
FT2756 Sensor Installer
Illustration 9 | g00867857 |
This illustration shows the dimensions for an FT2756 Sensor Installer. (A) This length is 146.0 ± 0.5 mm (5.75 ± 0.02 inch). (B) This length is 22 ± 4 mm (0.9 ± 0.2 inch). (C) This length is 25.4 ± 0.5 mm (1.00 ± 0.02 inch). (D) This length is 19.05 ± 0.05 mm (0.750 ± 0.002 inch). (E) This is a medium knurl. (F) This maximum radius is 0.13 mm (0.005 inch). (G) This diameter is 70.218 ± 0.013 mm (2.7645 ± 0.0005 inch). (H) This diameter is 25.4 ± 1.0 mm (1.00 ± 0.04 inch). (I) This radius is 1.5 ± 0.5 mm (0.06 ± 0.02 inch). (J) This diameter is 74.511 ± 0.013 mm (2.9335 ± 0.0005 inch). (K) This diameter is 50.8 ± 1.0 mm (2.00 ± 0.04 inch). (L) This diameter is 88.9 ± 1.0 mm (3.50 ± 0.04 inch). (M) This diameter is 108.0 ± 0.5 mm (4.25 ± 0.02 inch). |
FT2757 Seal Installer
Illustration 10 | g00867906 |
This illustration shows the dimensions for an FT 2757 Sensor Installer. (A) This length is 27.0 ± 1.0 mm (1.06 ± 0.04 inch). (B) This length is 88.9 ± 1.0 mm (3.50 ± 0.04 inch). (C) This diameter is 25.4 mm (1.00 inch). (D) This diameter is 9.5 ± 0.5 mm (0.37 ± 0.02 inch). (E) This chamfer is 1.5 ± 0.5 mm (0.06± 0.02 inch) by 45 degrees. (F) This maximum radius is 0.5 mm (0.02 inch). |