- Load Haul Dump (LHD):
- R1600 (PIN: 9EW)
The tightening procedure that is used with the torque wrench for the 132-3208 Cylinder Head Group has been revised. The revised tightening procedure follows.
Cylinder Head
Illustration 1 | g00729777 |
3176C Cylinder Head |
Note: There are currently two types of cylinder head bolts that are being used. The first type is a full shank design that is shown in Illustration 2. The second type is a reduced shank design that is shown in Illustration 3.
Note: Lubricate the following areas with 6V-4876 Lubricant prior to assembly: bolt threads, underside of the bolt heads and washers.
Illustration 2 | g00729779 |
Cylinder head bolt with full shank design |
(A) This is a reference dimension for the diameter of the shank of the cylinder head bolt. This bolt has a full shank diameter. ... 15.73 mm (0.619 inch)
Use the following procedure in order to tighten the cylinder head bolts with the full shank design:
- Tighten bolt (1) through bolt (26) in a numerical sequence.
Tighten the bolts to the following torque. ... 150 ± 15 N·m (110 ± 11 lb ft)
- Tighten bolt (1) through bolt (26) again in a numerical sequence.
Tighten the bolts again to the following torque. ... 150 ± 15 N·m (110 ± 11 lb ft)
- Place an index mark on bolt (1) through bolt (26). Rotate bolt (1) through bolt (26) in a numerical sequence.
Rotate the bolts in a clockwise direction. ... 90 degrees (1/4 turn)
- Loosen bolt (1) through bolt (26) until the washers are loose under the bolt heads.
- Tighten bolt (1) through bolt (26) in a numerical sequence.
Tighten the bolts to the following torque. ... 150 ± 15 N·m (110 ± 11 lb ft)
- Tighten bolt (1) through bolt (26) again in a numerical sequence.
Tighten the bolts again to the following torque. ... 150 ± 15 N·m (110 ± 11 lb ft)
- Place an index mark on bolt (1) through bolt (26). Rotate bolt (1) through bolt (26) in a numerical sequence.
Rotate the bolts in a clockwise direction. ... 90 degrees (1/4 turn)
- Tighten bolt (27) through bolt (33) in a numerical sequence.
Tighten the bolts to the following torque. ... 28 ± 7 N·m (20 ± 5 lb ft)
Illustration 3 | g00729780 |
Cylinder head bolt with reduced shank design |
(B) This is a reference dimension for the diameter of the shank of the cylinder head bolt. This bolt has a reduced shank diameter. ... 14.88 mm (0.574 inch)
Use the following procedure in order to tighten the cylinder head bolts with the reduced shank design:
- Tighten bolt (1) through bolt (26) in a numerical sequence.
Tighten the bolts to the following torque. ... 160 ± 15 N·m (120 ± 11 lb ft)
- Tighten bolt (1) through bolt (26) again in a numerical sequence.
Tighten the bolts again to the following torque. ... 160 ± 15 N·m (120 ± 11 lb ft)
- Place an index mark on bolt (1) through bolt (26). Rotate bolt (1) through bolt (26) in a numerical sequence.
Rotate the bolts in a clockwise direction. ... 90 degrees (1/4 turn)
- Loosen bolt (1) through bolt (26) until the washers are loose under the bolt heads.
- Tighten bolt (1) through bolt (26) in a numerical sequence.
Tighten the bolts to the following torque. ... 160 ± 15 N·m (120 ± 11 lb ft)
- Tighten bolt (1) through bolt (26) again in a numerical sequence.
Tighten the bolts again to the following torque. ... 160 ± 15 N·m (120 ± 11 lb ft)
- Place an index mark on bolt (1) through bolt (26). Rotate bolt (1) through bolt (26) in a numerical sequence.
Rotate the bolts in a clockwise direction. ... 90 degrees (1/4 turn)
- Tighten bolt (27) through bolt (33) in a numerical sequence.
Tighten the bolts to the following torque. ... 28 ± 7 N·m (20 ± 5 lb ft)