2000/05/29 Caterpillar


Correction to Disassembly and Assembly , "Remove and Install Wheels, Bearings, and Duo-Cone Seals" {4208, 7561}

Usage:

R1300 6QW
Load Haul Dump (LHD):
R1300 (PIN: 6QW1-UP)
Disassembly and Assembly, RENR4609-01 (9EL9608-01), "R1300 Load Haul Dump Power Train", "Remove and Install Wheels, Bearings, and Duo-Cone Seals". This module is part of Service Manual, RENR4600, "(9EL9598), Volume 1 for the R1300 Load Haul Dump (LHD)".

The 8M-7911 Duo-Cone Seal Installer that is shown in the "Tools Needed" chart on page 26 is incorrect. The correct part number is 1U-6439 Duo-Cone Seal Installer.

Caterpillar Information System:

C-12, C-15 and C-16 Engines for Caterpillar Built Machines CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
3176C and 3196 Engines for Caterpillar Built Machines CID 0174 FMI 04 Fuel Temperature short to ground
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Install
3176C and 3196 Engines for Caterpillar Built Machines CID 0174 FMI 03 Fuel Temperature open/short to +batt
2000/05/29 Correction to Disassembly and Assembly , "Remove and Install Wheels, Bearings, and Duo-Cone Seals" {4208, 7561}
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Disassemble
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0172 FMI 04 Intake Manifold Air Temp short to ground
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0172 FMI 03 Intake Manifold Air Temp open/short to +batt
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Assemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Oil Cooler (Brake) - Remove
TH62, TH63, TH82 and TH83 Telehandlers Transfer Gear Oil Level - Check
2000/06/12 Improved Routing of the Wire for the Suspension Seat {7324}
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0273 FMI 03 Turbo Outlet Pressure open/short to +batt
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0273 FMI 04 Turbo Outlet Pressure short to ground
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0274 FMI 03 Atmospheric Pressure open/short to +batt
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0274 FMI 04 Atmospheric Pressure short to ground
C-9 Engine for MT735, MT745, MT755, MT765, MTC735, MTC745, MTC755, and MTC765 Agricultural Tractors CID 0274 FMI 13 Atmospheric Pressure calibration required
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Remove
TH62, TH63, TH82 and TH83 Telehandlers Transmission Breather - Clean
3508B and 3512B Engine Supplement for 776D, 777D, and 777D HAA Tractor/Off-Highway Trucks Accumulator (Refrigerant) Remove and Install
2000/06/19 Correction to Service Magazine, 9EP3441, 31 October 1999 , "New Thrust Washer Improves Service Life of Differential Group" {3258}
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Service Brakes - Remove and Install
2000/05/29 The Required Torque has been Increased for the Piston Retaining Nut in the Lift Cylinder {5102}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.