Hydraulic Tank (Torque Converter, Hoist, Brake, and Transmission) - Install
- Check all of the O-ring seals and the components for wear or damage. Replace the components, if necessary.
- Lubricate all of the O-ring seals lightly with the lubricant that is being sealed.
Show/hide table
Illustration 1 g00574322 - Use a suitable lift truck (not shown) in order to position hydraulic tank (1) for installation. The weight of hydraulic tank (1) is
367 kg (810 lb) .Show/hide tableIllustration 2 g00506994 Show/hide tableIllustration 3 g00506995 - Install cap (23). Install two bolts (22) and the washers.
- Install cap (20). Install two bolts (19) and the washers.
- Connect hose assembly (21) and (24).
Show/hide table
Illustration 4 g00507002 - Install one bolt (18), the locknut, the washers and the mountings.
Show/hide table
Illustration 5 g00506992 (12) Transmission return port.
(13) Converter inlet relief port.
(14) ( 15) ( 16) Brake cooling ports.
(17) Control valve return port. - Install the following hose assemblies: (17), (16), (15), (14), (13) and (12).
Show/hide table
Illustration 6 g00506987 (8) Converter scavenger return port.
(9) Parking brake drain port.
(10) Parking brake lip seal drain port.
(11) Brake make-up tank return port . - Install the following hose assemblies: (11), (10), (9) and (8).
Show/hide table
Illustration 7 g00506970 (2) Transmission suction port.
(3) ( 4) Hoist pump suction port.
(5) Brake cooling suction port.
(6) Converter suction port.
(7) Auxiliary port. - Install the following hose assemblies: (7), (6), (5), (4), (3) and (2).
Show/hide table
Illustration 8 g00506961 - Fill tank (A) of hydraulic tank (1) with hydraulic oil to the correct level. Refer to Operation and Maintenance Manual, SEBU7173, "Hoist, Torque Converter and Brake Tank Oil - Change" for the correct procedure.
- Fill tank (B) of hydraulic tank (1) with hydraulic oil to the correct level. Refer to Operation and Maintenance Manual, SEBU7173, "Transmission Tank Oil - Change" for the correct procedure.
Show/hide table
Personal injury or death can result from air in the oil for the brake hydraulic system.
Air in the system can prevent complete brake application and it is possible that the wheels on the machine can not be stopped.
Air must not be in the oil for the brake hydraulic system to function properly.
- Purge the air from the hydraulic oil in the brake hydraulic system. Refer to Systems Operation/Testing and Adjusting, SENR1494, "Brake System Air - Purge" for the correct procedure.
Note: Cleanliness is an important factor. Before the installation procedure, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble.
End By:
- Install the oil filter and base (torque converter). Refer to Disassembly and Assembly, SENR1490, "Oil Filter and Base (Torque Converter) - Install".
- Install the retaining cable. Refer to Disassembly and Assembly, "Truck Body Retaining Cable - Remove and Install".
- Remove the wheel chocks. Refer to Disassembly and Assembly, "Wheel Chock - Remove and Install".
Caterpillar Information System:
69D, 769D , 773D, 773E, 776D, 777D, 784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Braking System Sensors
3306C Engines for Caterpillar Built Machines Fan Drive
583R Pipelayer Power Train Transmission and Bevel Gears - Install
Caterpillar Monitoring System Gear Display Mode
3406E On-Highway Engine Pistons and Connecting Rods - Disassemble
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0825 FMI 06 Lamp (Red Payload) Current Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0825 FMI 05 Lamp (Red Payload) Current Below Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0825 FMI 03 Lamp (Red Payload) Voltage Above Normal - Test
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Hoist Cylinder - Disassemble
550 Wheel Harvester, 570 Wheel Harvester and 580 Wheel Harvester Hydraulic System Piston Pump (Implement) - 550 Wheel Harvester
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0824 FMI 06 Lamp (Green Payload) Current Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0824 FMI 05 Lamp (Green Payload) Current Below Normal - Test
550 Wheel Harvester, 570 Wheel Harvester and 580 Wheel Harvester Hydraulic System Pressure Reducing Valve (Swing Motor Back Pressure)
550 Wheel Harvester, 570 Wheel Harvester and 580 Wheel Harvester Hydraulic System Implement Control System
554 Forwarder and 574 Forwarder Hydraulic System Load Sensing Signal System
554 Forwarder and 574 Forwarder Hydraulic System Gate Control System
554 Forwarder and 574 Forwarder Hydraulic System Main Hydraulic System
554 Forwarder and 574 Forwarder Hydraulic System Monitoring and Control System
554 Forwarder and 574 Forwarder Hydraulic System Oscillation Lock System
554 Forwarder and 574 Forwarder Hydraulic System Steering System
554 Forwarder and 574 Forwarder Hydraulic System Implement Pump
554 Forwarder and 574 Forwarder Hydraulic System Swing System
554 Forwarder and 574 Forwarder Hydraulic System Troubleshooting
3406C Engines for Caterpillar Built Machines Compression Brake - If Equipped