Engine Speed Sensor - Remove and Install
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove cable strap (1).
- Disconnect harness assembly (2).
Show/hide table
Illustration 2 g06367968 - Remove engine speed sensor (3).
Show/hide table
Illustration 1 | g06367955 |
- Install engine speed sensor (3).
- Turn the engine speed sensor (3) until there is contact with the tooth of the flywheel. Turn the engine speed sensor for 1/2 of a turn away from the tooth of flywheel.
- Tighten engine speed sensor (3) to a torque of
25 ± 5 N·m (18 ± 4 lb ft) .Show/hide tableIllustration 4 g06367955 - Connect harness assembly (2).
- Install cable strap (1).
Show/hide table
Illustration 3 | g06367968 |
Caterpillar Information System:
C175 Tier 4 Final Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
New Jacket Water Elbow and Adapter are Now Used on Certain Cat® Engines {1355, 1380, 1393} New Jacket Water Elbow and Adapter are Now Used on Certain Cat® Engines {1355, 1380, 1393}
Documentation Required for Diesel Exhaust Fluid (DEF) Injector Failures on Certain 3500 and C175 Machine Engines {108H, 108K, 108Z, 1091} Documentation Required for Diesel Exhaust Fluid (DEF) Injector Failures on Certain 3500 and C175 Machine Engines {108H, 108K, 108Z, 1091}
C27 and C32 Generator Set Engines Cylinder Head - Remove
New Engine and Aftertreatment Software are Now Available for Certain 797F Off-Highway Truck Engines {1920, 7620} New Engine and Aftertreatment Software are Now Available for Certain 797F Off-Highway Truck Engines {1920, 7620}
New Firmware is Available for Certain Power Modules {7610} New Firmware is Available for Certain Power Modules {7610}
Perform Circuit Breaker Inspection on Certain Cat® Engines {1420} Perform Circuit Breaker Inspection on Certain Cat® Engines {1420}
Procedure to Install Brush Holder Assembly to End Frame on All Engines {1405} Procedure to Install Brush Holder Assembly to End Frame on All Engines {1405}
Procedure for Replacing Regulator Kit on All Engines {1405} Procedure for Replacing Regulator Kit on All Engines {1405}
Procedure to Install Brush Holder Assembly in All Engines {1453} Procedure to Install Brush Holder Assembly in All Engines {1453}
Procedure to Install Terminal Kit on All Engines {1453} Procedure to Install Terminal Kit on All Engines {1453}
Installation of Repair Kit-Solenoid Plunger Assembly on All Engines {1453} Installation of Repair Kit-Solenoid Plunger Assembly on All Engines {1453}
G3512 Generator Set Engine Throttle Differential Pressure Sensor - Remove and Install
New Seal Installer for Certain Reman Sea Water Pumps is Now Available on Certain C18 Marine Engines {1371} New Seal Installer for Certain Reman Sea Water Pumps is Now Available on Certain C18 Marine Engines {1371}
325 Excavator Bucket Linkage - Inspect/Adjust
325 Excavator Condenser (Refrigerant) - Clean
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Bank Valve - Two
Charging System Troubleshooting Guide Has Been Updated for All Machines {1406, 7569} Charging System Troubleshooting Guide Has Been Updated for All Machines {1406, 7569}
Charging System Troubleshooting Guide Has Been Updated for All Engines {1406, 7569} Charging System Troubleshooting Guide Has Been Updated for All Engines {1406, 7569}
New Special Instruction to Interpret Scheduled Oil Sampling (SOS) is Now Available for All C27 and C32 Machine Engines {1000, 7571} New Special Instruction to Interpret Scheduled Oil Sampling (SOS) is Now Available for All C27 and C32 Machine Engines {1000, 7571}
New Stainless Steel Aftercooler Core is Now Available for Certain G3520H Generator Sets {1063} New Stainless Steel Aftercooler Core is Now Available for Certain G3520H Generator Sets {1063}
325 Excavator Cooling System Coolant Extender (ELC) - Add
325 Excavator Cooling System Coolant Level - Check
325 Excavator Cooling System Coolant Sample (Level 1) - Obtain