Engine Oil Pan
Show/hide table
Illustration 1 | g06321738 |
Show/hide table
Illustration 2 | g06321792 |
204-5154 Oil Pan Gp |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
1 | 16 | 0L-1143 Bolt | Use the following procedure to tighten the sequence for hand torque wrench or single spindle torque tool:
1. Tighten the end bolts followed by the left and right side bolts. 2. Start with a bolt towards the center of the right and left side of the pan and work towards the ends. 3. Again tighten the three center bolts of the left and right side. 4. Again tighten all the end bolts. |
2 | - | - | Before assembly, apply Loctite Quickstix 534 HI-Tack gasket sealant between gasket and oil pan to hold the gasket in place. Do not apply sealant at puzzle joints or T-joints. |
3 | - | - | As required, apply Loctite RTV Silicone Clear to the joints of the gasket. |
4 | 41 | 0T-0065 Bolt | Use the following procedure to tighten the sequence for hand torque wrench or single spindle torque tool:
1. Tighten the end bolts followed by the left and right side bolts. 2. Start with a bolt towards the center of the right and left side of the pan and work towards the ends. 3. Again tighten the three center bolts of the left and right side. 4. Again tighten all the end bolts. |
5 | 3 | 3P-0654 O-Ring Seal | Before assembly, apply 1P-0808 Multipurpose Grease to lubricate the bores. |
6 | 2 | 0S-1590 Bolt | To prevent stress on the tube assembly, use the following tightening procedure during assembly:
1. Tighten two bolts (8) to 2. Then tighten two bolts (6) to |
7 | 2 | 7X-1547 O-Ring Seal | Before assembly, apply 1P-0808 Multipurpose Grease to lubricate the bores. |
8 | 4 | 0S-1588 Bolt | To prevent stress on the tube assembly, use the following tightening procedure during assembly:
1. Tighten two bolts (8) to 2. Then tighten two bolts (6) to |
9 | 2 | 4B-2363 Oil Drain Plug | Torque to |
Caterpillar Information System:
3516C IMO III Petroleum Engines Auxiliary Fuel Filter Housing - Install
3516C IMO III Petroleum Engines Auxiliary Fuel Filter Housing - Remove
3500 Engines Engine Oil Pan
3500 Engines Engine Oil Pan
3500 Engines Crankcase Breather
SR5 Electric Power Generation Space Heater - Test
SR5 Electric Power Generation Rotating Rectifier - Inspect/Test
3516C IMO III Petroleum Engines Vibration Damper - Remove and Install
SR5 Electric Power Generation Rotating Rectifier - Test - Discrete Diode Test
3516C IMO III Petroleum Engines Fuel Filter Housing - Install
3516C IMO III Petroleum Engines Fuel Filter Housing - Remove
320D3 and 323D3 Excavators Machine System Specifications Auxiliary Hydraulic Lines
3516C IMO III Petroleum Engines Turbocharger - Remove
3500 Engines Atmospheric Pressure Sensor
3500 Engines Fuel Filter (Primary)
G3512 Gas Engine Water Lines
3500 Engines Water Lines
3500 Engines Turbocharger Exhaust Temperature Sensor
3516C IMO III Petroleum Engines Air Shutoff - Remove and Install
C175-16 Petroleum Engine Sensor Signal (Analog, Passive) - Test
797F Tier 4 Off-Highway Truck Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
Air Cleaner Group May Crack on Certain 374F and 390F Excavators {1051, 1054} Air Cleaner Group May Crack on Certain 374F and 390F Excavators {1051, 1054}
320D3 and 323D3 Excavators Machine Electronic Control System Diagnostic Trouble Codes
3500 Engines Fuel Filter