Bearing - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 8T-0514 | Guide Stud | 2 |
B | 333-9726 | Polyethylene Film | - |
C | 154-6182 | Forcing Bolt | 2 |
D | 1H-3110 | Bearing Puller Gp | 1 |
1U-9889 | Crossblock | 1 | |
3H-0468 | Puller Plate | 2 | |
4C-9633 | Puller Stud | 2 | |
360-6964 | Hydraulic Cylinder | 1 | |
350-7769 | Electric Hydraulic Pump Gp | 1 | |
350-7768 | Electric Hydraulic Pump Gp | 1 |
Start By:
- Remove terminal box.
- Remove exciter.
Show/hide table
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death. |
- Remove bolts (1) and bolts (2). Remove bolts (4) and remove terminal bracket (3).
Show/hide table
Illustration 2 g03890864 - Install Tooling (B) between to rotor and the stator to ensure that these parts do not contact one another. Remove two bolts (5) and install Tooling (A). Remove remaining bolts (5).
Show/hide table
Illustration 3 g03891329 - Remove bolts (7) and remove retainer (6). Repeat for the other side.
Show/hide table
Illustration 4 g03890963 - Install Tooling (C) and tighten until barrel (8) begins to separate from bearing housing (9). Thread suitable lifting device through gap to support bearing housing (9). The weight of bearing housing (9) is approximately
100 kg (220 lb) . Remove bearing housing (9).Show/hide tableIllustration 5 g03891376 - Install Tooling (D). Use suitable lifting device to support Tooling (D). Use Tooling (D) to remove bearing (10).
Show/hide table
Illustration 1 | g03890837 |
- Install bearing (10) in the reverse order of removal.
- Raise temperature of bearing (10) to assist installation.
Caterpillar Information System:
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Turbocharger Cartridge - Install
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Turbocharger Cartridge - Remove
G3606 and G3608 Engines Cylinder Head - Install - For EAME use only
Energy Storage System Battery Management Unit - Replace
Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000} Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
C1.7 and C2.2 Industrial Engines Exhaust Gas Recirculation Valve - Clean
Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000} Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000} Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
EMCP4.2B Custom Text String Is Not Shown
EMCP4.2B Diagnostic Trouble Code List
EMCP4.2B Analog Input Programming
EMCP4.2B Output Programming
C3.3B and C3.8 Engines for Caterpillar Built Machines DEF Concentration Is Incorrect
G3606 and G3608 Engines Crankshaft - Remove
A New Pressure Switch Is Used on Certain G3500 and G3600 Engines {7400} A New Pressure Switch Is Used on Certain G3500 and G3600 Engines {7400}
G3606 and G3608 Engines Crankshaft - Install
C15 Generator Set Maintenance Interval Schedule - Prime Power
C15 Generator Set Maintenance Interval Schedule - Standby
C15 Generator Set Maintenance Interval Schedule - Emergency Standby Power
C3.3B and C3.8 Engines for Caterpillar Built Machines DEF Module Does Not Respond
C1.7 and C2.2 Industrial Engines Engine Valve Lash - Check
C1.7 and C2.2 Industrial Engines Fuel System - Prime
DE Series Generator Set with Cat C1.1, C1.5, and C2.2 Engines Maintenance Interval Schedule - Prime Power
DE Series Generator Set with Cat C1.1, C1.5, and C2.2 Engines Maintenance Interval Schedule - Standby