Camshaft - Remove
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 8T-3029 | 凸轮轴支架 | 1 |
1U-6311 | 盘 | 1 | |
B | 1P-2382(1) | 扳手适配器 | 1 |
9U-5932(1) | 扭矩扳手加长件 | 1 | |
C | 6V-6080 | 扭矩倍增器总成 | 1 |
5P-1748 | 套筒 | 1 |
Show/hide table
(1) | 只需一个工具。 确保发动机使用了正确的工具。 |
开始:
- 拆下发动机机油滤清器壳体。
- 拆下气门挺杆。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 断开线束 (1)。
Show/hide table
图 2 g03863803 - 断开线束组件 (2)。
Show/hide table
图 3 g03863810 - 拆下螺栓 (3)、托架组件 (4) 和线束组件。
Show/hide table
图 4 g03863837 - 拆下螺栓 (5)、夹子 (6)、螺栓 (8) 和支架 (7)。
- 拆下螺栓 (9)、螺栓 (10)、螺栓 (11) 和支架 (12)。
Show/hide table
图 5 g03863875 - 拆下螺栓 (13) 和凸轮轴盖 (14)。
- 重复步骤 4 至步骤 6,以拆下其余的凸轮轴盖。
Show/hide table
图 6 g03863967 - 拆下螺栓 (15) 和盖 (16)。
Show/hide table
图 7 g03864023 必须旋转发动机,以便拆下将凸轮轴齿块 (19) 固定到位的所有螺栓。 - 使用工具 (B) 松开凸轮轴齿块 (19) 外侧的螺栓 (17)。
注: 识别凸轮轴齿块和凸轮轴轴颈的正确方位,以便于安装。
- 将工具 (A) 安装在凸轮轴齿块 (19) 下面。
- 小心地将凸轮轴前部分移向发动机前部。 这样做是为了断开凸轮轴齿块各端中的定位销。
- 小心地将凸轮轴齿块 (19) 从工具 (A) 上的发动机上移出。
- 将适当的起吊设备连接到涡轮增压器 (19) 上。 凸轮轴齿块 (19) 的重量大约为
31 kg (69 lb) 。 在凸轮轴齿块上作识别标记,以便于安装。 - 从每个凸轮轴轴颈上拆下隔套。 将工具 (A) 从发动机上拆下。
- 拆下将凸轮轴轴颈 (18) 固定在其他凸轮轴齿块上的螺栓。
- 将凸轮轴轴颈 (18) 滑出凸轮轴轴承。 从发动机上拆下凸轮轴轴颈 (18)。 从轴颈上拆下隔套。
Show/hide table
图 8 g03864342 - 拆下螺栓 (21)、盖 (20) 和 O 形密封圈。
Show/hide table
图 9 g03864352 - 断开线束组件 (24)。 拆下螺栓 (26) 和托架组件 (27)。
- 断开线束组件 (25) 和线束组件 (28)。
- 拆下螺栓 (22)、壳体 (23) 和 O 形密封圈。
Show/hide table
图 10 g03864381 - 拆下螺栓 (30) 及正时和转速驱动装置 (29)。
Show/hide table
图 11 g03864399 - 接合并锁定手动盘车总成,防止松开螺栓 (33) 后曲轴旋转。
- 从曲轴和凸轮轴上卸下定时销。
- 使用工具 (C) 拧松螺栓 (33)。
- 拆卸螺栓 (33) 和垫圈 (34)。
- 拆下螺栓 (32) 和板 (35)。
- 将垫圈 (34) 放到凸轮轴和板 (35) 之间。 安装螺栓 (33)。
- 安装螺栓 (32) 并用手拧紧。
注: 当凸轮轴主动齿轮 (33) 与凸轮轴锥面脱开时,确保已安装螺栓 (33) 固定凸轮轴主动齿轮 (31)。
- 均匀拧紧螺栓 (32),以便将凸轮轴驱动齿轮 (33) 脱开凸轮轴锥面。
- 将适当的起吊设备连接在凸轮轴驱动齿轮 (31) 上。 凸轮轴驱动齿轮 (31) 的重量大约为
41 kg (90 lb) 。 拆下螺栓 (32)、螺栓 (33)、板 (35)和垫圈 (34)。 将凸轮轴主动齿轮 (31) 从后壳体上拆下。 - 对其余的凸轮轴齿块重复步骤 9 至步骤 16。
Show/hide table
图 1 | g03863769 |
Caterpillar Information System:
336F and 340F Excavators Machine System Specifications Cylinder Guard
794 AC Off-Highway Truck Field Assembly Lighting - Install
G3606 and G3608 Engines Housing (Front) - Remove and Install
794 AC Off-Highway Truck Field Assembly Air Conditioner Lines - Install
XQ2000 Power Module Product Description
3516E Generator Set Maintenance Interval Schedule - Standby
Repairing Small Cracks In Base Edge Assemblies{0679, 6001, 6120, 6801} Repairing Small Cracks In Base Edge Assemblies{0679, 6001, 6120, 6801}
352F Excavator Safety Messages
352F Excavator Lifting Capacities
352F Excavator Specifications - Long Reach Configuration
C280 Marine Engines Camshaft Timing
HPU300 Hydraulic Power Pack Lifting and Tying Down
3516E Generator Set Safety Messages
3516E Generator Set Configuration Parameters
3516E Generator Set Product Lifting
3516E Generator Set Engine Oil Level - Check
3516E Generator Set Plate Locations and Film Locations
794 AC Off-Highway Truck Field Assembly Tire and Rim - Install
120 and 120 AWD Motor Grader Engine Shutdown Switch - Check
Improved Alternator Mounting Groups Are Now Used on Certain C18 Engines {1405} Improved Alternator Mounting Groups Are Now Used on Certain C18 Engines {1405}
794 AC Off-Highway Truck Field Assembly Body and Canopy - Install
2015/08/21 New Harness Routing Used For Certain G3516H Engines {1408}
2015/07/17 The 359-9613 Sensor and Mounting Gp Is Missing On Certain CG137-12 Engines {7400}
2015/07/17 The Cabinet Isolator Mounts And Diesel Exhaust Fluid (DEF) Hoses Are Removed From The Parts Kit For Certain Retrofit Aftertreatment Products {7451}