Fuel Tank - Install
Parts and Specification Information
Show/hide table
Illustration 1 | g03839171 |
Note: Verify that all parts are shipped and undamaged for preparation of assembly. Missing or damaged parts can be ordered prior to assembly to avoid delays during assembly.
Show/hide table
Personal injury or death can occur from heavy components falling during removal or installation. Properly support the component with a suitable lifting device during removal or installation. |
Show/hide table
Climbing equipment may be required to access this service point. Refer to the Operation and Maintenance Manual, "Mounting and Dismounting" topic for safety information. |
Show/hide table
Item | Part Number | Description | Qty | Specification | Approximate Weight |
1 | 442-2535 | Fuel Tank Gp | 1 | ||
442-2528 | Fuel Tank Mounting Gp | 1 | |||
2 | 7X-0429 | Bolt | 2 | ||
3 | 7X-0533 | Hard Washer | 2 | ||
4 | 7X-0451 | Full Nut | 2 | ||
5 | 3J-1805 | Bolt | 2 | ||
6 | 434-5473 | Spacer | 2 | ||
7 | 196-3187 | Elbow | 2 | ||
8 | 442-2739 | Hose As | 1 | ||
9 | 432-8058 | Clamp As | 1 | ||
10 | 434-5587 | Pipe Coupling | 2 | ||
11 | 434-5630 | Fitting | 1 | ||
12 | 300-8495 | Receiver | 1 | ||
13 | 432-8017 | Clamp | 1 | ||
14 | 432-8042 | Guard As | 1 |
- Use a suitable lifting device to position fuel tank and mounting group (1) and install with two bolts (2), two hard washers (3), and two full nuts (4).
Show/hide table
Illustration 3 g03839613 - Secure fuel tank and mounting group (1) with two bolts (5) and two spacers (6).
Show/hide table
Illustration 4 g03839683 - Install elbow (7) to the back of the fuel fill line. Install hose assembly (8) and clamp assembly (9) to run a fuel fill line to the left side of the machine.
- Install two pipe couplings (10) and fitting (11) through the mounts on the side of the hydraulic tank.
- Install receiver (12), clamp (13), and guard assembly (14) on the end of the line.
Show/hide table
Illustration 5 g03840262 Show/hide tableIllustration 6 g03840266 - Connect the 442-2551 Fuel Lines Gp (A) to the fuel supply and fuel return connections.
- Connect 442-3753 Chassis Harness As (B) to the fuel level sensor in the fuel tank.
Show/hide table
Illustration 2 | g03839182 |
Caterpillar Information System:
3512C Generator Set Engine Fuel Filter Housing - Remove and Install
3512C Generator Set Engine Electronic Control Module (Engine) - Remove and Install
Installation Procedure for the Prelubrication Oil Pump on Certain G3500 Engines{1319} Installation Procedure for the Prelubrication Oil Pump on Certain G3500 Engines{1319}
3516C High Displacement Engine Electrical Power Supply - Test
3516B Generator Set Engines with Dynamic Gas Blending Fuel Consumption Is Excessive
3516C High Displacement Engine Cooling Fan Control - Test
3512C Generator Set Engine Air Starting Motor - Remove and Install
3512C and 3516C Industrial Engines Exhaust Manifold
3516B Generator Set Engines with Dynamic Gas Blending Engine Shutdown Occurs Intermittently
3516B Generator Set Engines with Dynamic Gas Blending Engine Stalls at Low RPM
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Engine Air Filter Element - Clean/Replace
2015/06/26 New Software Is Used on 3512C Engines in 6060 Hydraulic Shovels {1920}
3516C High Displacement Engine Ether Starting Aid - Test
G3606 and G3608 Engines Crankcase Cover - Remove and Install
3516C High Displacement Engine Sensor Signal (Analog, Active) - Test
3516C High Displacement Engine Sensor Signal (PWM) - Test
3516C High Displacement Engine Sensor Supply - Test
C4.4 and C7.1 Engines Configuration Parameters
C4.4 and C7.1 Engines Diagnostic Trouble Codes
C4.4 and C7.1 Engines Acceleration Is Poor or Throttle Response Is Poor
C4.4 and C7.1 Engines Event Codes
C4.4 and C7.1 Engines Coolant Level Is Low
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Wheel Lean Bearings - Lubricate
C4.4 and C7.1 Engines Coolant Temperature Is High