Oil Contains Coolant
- Water pump
- Engine oil cooler core
- Water-cooled turbocharger
- Cylinder head gasket
- Cylinder head
- Cylinder liner
- Cylinder block
Show/hide table
Troubleshooting Test Steps | Values | Results |
1. Water pump A. Check the weep hole in the water pump for blockage. B. Check the water pump seals. |
Water pump |
Result : The water pump is leaking. Repair : Replace the water pump. Refer to the Disassembly and Assembly manual for more information. Result : The water pump is not leaking. Proceed to Test Step 2. |
2. Check for leaks in the oil cooler core. |
Oil cooler core |
Result: No leak is found in the oil cooler core. Proceed to Test Step 3. Result: There is a leak found in the oil cooler core. Repair : Replace the oil cooler core. |
3. If the engine is equipped with a water-cooled turbocharger, inspect the turbocharger for cracks. |
Turbocharger |
Result: The turbocharger is not cracked. Proceed to Test Step 4. Result: The turbocharger is cracked. Repair : Replace the turbocharger. Refer to the Disassembly and Assembly Manual for more information. |
4. Check the cylinder liner projection. |
Liner projection |
Result: Cylinder liner projection is OK. Proceed to Test Step 5. Result: Cylinder liner projection is NOT OK. Repair : Install a new cylinder head gasket and new water seals in the spacer plate. Refer to the Disassembly and Assembly manual. |
5. Check for cracks in the cylinder head. |
Cracks in cylinder head |
Result: There are no cracks in the cylinder head. Proceed to Test Step 6. Result: There are cracks in the cylinder head. Repair : Repair the cylinder head and/or replace the cylinder head. Refer to the Disassembly and Assembly manual. |
6. Check for cracked cylinder liners. |
Cracks in cylinder liners |
Result: There are no cracks in the cylinder liners. Proceed to Test Step 7. Result: There are cracks in the cylinder liners. Repair : Replace any cracked cylinder liners. Refer to the Disassembly and Assembly manual. |
7. Inspect the cylinder block for cracks. |
Cracks in cylinder block. |
Result: The cylinder block is not cracked. STOP Result: The cylinder block is cracked. Repair : Repair the cylinder block or replace the cylinder block. STOP |
Caterpillar Information System:
C18 Marine Engine Maintenance Interval Schedule
C4.4 Engines Solenoid Valve - Test - Solenoid Valves that Connect to the Engine ECM
C4.4 Engines Solenoid Valve - Test - Solenoid Valves that Connect to the Dosing Control Unit (DCU)
C4.4 Engines Sensor Signal (Analog, Passive) - Test
C4.4 Engines Sensor Signal (Analog, Active) - Test
C4.4 Engines Sensor Supply - Test
C4.4 Engines Sensor Calibration Required - Test
C4.4 Engines Sensor (Data Link Type) - Test
C4.4 Engines Power Take-Off - Test
C7 and C9 Industrial Engines Exhaust Has Excessive White Smoke
CG137-08 and CG137-12 Engines Safety Messages
C4.4 Engines NOx Sensor - Test
XQ400 Power Module General Hazard Information
CG137-12 Generator Set Model View Illustrations
C18 Marine Engine Additional Messages
C18 Marine Engine Maintenance Interval Schedule
XQ400 Power Module Product Description
C7 and C9 Industrial Engines Oil Consumption Is Excessive
C7 and C9 Industrial Engines Cylinder Is Noisy
C15 and C18 Engines for Caterpillar Built Machines ECM Does Not Communicate with Other Modules
C7 and C9 Industrial Engines Engine Cranks but Does Not Start
CG137-08 and CG137-12 Engines Plate Locations and Film Locations
XQ400 Power Module Alarms and Shutoffs
XQ400 Power Module Electronic Modular Control Panel 4 (EMCP 4) - EMCP 4.4