Centershift Lock Bar and Bushings - Remove
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1U-9200 | Lever Puller Hoist | 1 |
B | 123-3804 | Bearing Puller Adapter | 1 |
1U-7758 | Stud | 1 | |
9U-6832 | Nut | 1 | |
4K-0684 | Hard Washer | 1 | |
6V-3170 | Double Acting Cylinder | 1 | |
350-7768 | Electric Hydraulic Pump Gp (115V) | 1 | |
350-7769 | Electric Hydraulic Pump Gp (230V) | 1 | |
5F-7693 | Spacer As | 1 | |
C | 1P-1832 | Adapter | 1 |
5P-4776 | Tool Stud | 1 | |
9U-6833 | Nut | 1 | |
5P-8250 | Washer | 1 | |
6V-3160 | Double Acting Cylinder | 1 | |
350-7768 | Electric Hydraulic Pump Gp (115V) | 1 | |
350-7769 | Electric Hydraulic Pump Gp (230V) | 1 | |
5F-7693 | Spacer As | 1 |
Show/hide table
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death. |
- Connect the steering frame lock. Refer to Operation and Maintenance Manual, "Steering Frame Lock" for the correct procedure.
- Lower the blade to the ground.
- Retract the centershift lock pin. Refer to Operation and Maintenance Manual, "Centershift Lock" for the correct procedure.
Show/hide table
Illustration 1 g01397540 Typical Example - Attach Tooling (A) and a suitable lifting device to blade lift arms (1).
Show/hide table
Illustration 2 g01397553 - Attach a suitable lifting device to centershift cylinder (2). The weight of centershift cylinder (2) is approximately
54 kg (120 lb) . - Remove bolts (3) and cap (4).
Note: Note the shims for installation purposes.
- Use the machine to retract the cylinder rod. Lower centershift cylinder (2) to drawbar (5).
- Release the system pressure. Refer to Operation and Maintenance Manual, "System Pressure - Release".
Show/hide table
Illustration 3 g01397593 - Attach a suitable lifting device to centershift lock bar (8). The weight of centershift lock bar (8) is approximately
77 kg (170 lb) . - Remove bolts (6) and lock (9). Repeat this step for the opposite side.
- Remove pin (7). Lower centershift lock bar (8) to the drawbar.
Show/hide table
Illustration 4 g01397600 - Attach a suitable lifting device to opposite side of centershift lock bar (8).
- Remove pin (10) and lower centershift lock bar (8) to the drawbar.
Show/hide table
Illustration 5 g01397601 - Remove seals (11).
Note: Note the orientation of seals (11) for assembly purposes.
Show/hide tableIllustration 6 g01397603 Show/hide tableIllustration 7 g01397605 - Use Tooling (B) to remove bearing (12).
- Use Tooling (C) to remove bushings (13).
Caterpillar Information System:
CX31-P600 Petroleum Transmission Maintenance Interval Schedule
C18 Petroleum Engine Product Description
14L Motor Grader Machine Systems Centershift Lock Bar and Bushings - Install
Bench Test Procedure for a CX31 On Highway Truck or AD22 Articulated Truck Transmission {3030, 3073} Bench Test Procedure for a CX31 On Highway Truck or AD22 Articulated Truck Transmission {3030, 3073}
Disassembly and Assembly Procedure for 3N-8891 Sea Water Heat Exchanger Gp {1379} Disassembly and Assembly Procedure for 3N-8891 Sea Water Heat Exchanger Gp {1379}
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Air Inlet and Exhaust Lines
C18 Petroleum Engine Maintenance Interval Schedule
C4.4 Industrial Engine Belt - Inspect
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Air Inlet and Exhaust Lines
C4.4 Industrial Engine Belt Tensioner - Check
2013/10/21 Recommendations For Parameters and Update Rates On PL1000T For Certain C32, 3500, and G3500 Engines {1926}
UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Electrical Connections
C18 Petroleum Engine Gauges and Indicators
C18 Petroleum Engine Monitoring System
Retrofit SCR Aftertreatment Catalyst (SCR) - Replace
EMCP4.1/EMCP4.2 Integrated Voltage Regulator
Retrofit Diesel Particulate Filter (DPF) Systems Glossary
Retrofit SCR Aftertreatment Diesel Particulate Filter - Clean/Inspect
Retrofit SCR Aftertreatment Exhaust Inlet Nitrogen Oxide Sensor - Inspect/Replace
Retrofit SCR Aftertreatment Exhaust Outlet Nitrogen Oxide Sensor - Inspect/Replace
Retrofit SCR Aftertreatment Catalyst (DOC) - Replace
Retrofit SCR Aftertreatment Diesel Particulate Filter - Replace
2013/11/21 New Engine Software is Now Used on Certain C32 Marine Engines {1901, 1920}
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Air Inlet and Exhaust Lines